How To Fix A Paper Jam Error On A Brother Laser Printer (2026)
A Brother laser printer names the place where the paper is stuck, so the message on the display tells you where to look.
Brother’s guides give a separate fix for each of the Jam Tray, Jam Inside, Jam Rear and Jam 2-sided messages.
This guide lists those fixes and what to do when the jam message stays after the paper is gone.
Quick answer: where to look for each jam message
| Message | Where the paper is stuck | What Brother says to do |
|---|---|---|
| Jam Tray 1 | In the paper tray shown on the display | Pull the tray out completely and remove the jammed paper |
| Jam Inside | Inside the machine | Open the front cover, take out the toner and drum assembly, and clear the paper |
| Jam Rear | At the back of the machine | Open the fuser cover, remove the paper, and close it |
| Jam 2-sided | In the 2-sided tray or near the fuser | Pull out both trays and open the back cover |
| Cover is Open | Front or fuser cover not closed, or a jam at the back at power-on | Close the cover and check behind the back cover |
Before you start
Brother warns that the machine’s internal parts will be extremely hot after printing, so wait for them to cool before touching the fuser area.
Brother’s guide for 2-sided jams says to leave the machine on for 10 minutes so its fan can cool the hot parts.
Fix Jam Tray 1
Jam Tray 1 means the paper is stuck in the tray named on the display.
- Pull the paper tray completely out of the machine.
- Gently remove all the jammed paper.
- Push the tray firmly back in.
Brother’s DCP-L2640DW series page also says to reinsert the tray firmly, so a half-seated tray can bring the message back.
Fix Jam Inside
Jam Inside means the paper is stuck inside the machine.
- Open the front cover.
- Remove the toner cartridge and drum unit assembly.
- Remove the jammed paper.
- Put the assembly back and close the front cover.
On some models Brother adds that if the message remains, you press Start.
Fix Jam Rear
Jam Rear means the paper is stuck at the back of the machine.
- Open the fuser cover.
- Remove all the jammed paper.
- Close the fuser cover.
If the message stays, Brother says to press Go on the HL-L2460DW, Start on some models, and Retry on others.
Fix Jam 2-sided
Jam 2-sided means the paper is stuck in the 2-sided tray or near the fuser.
Brother’s detailed steps for the HL-L2460DW and related models are below.
- Leave the machine on for 10 minutes so the fan can cool the hot parts.
- Pull the paper tray completely out of the front.
- Pull the 2-sided tray completely out of the back.
- Remove the jammed paper from the machine or the 2-sided tray.
- Check for paper that may have jammed under the machine.
- If nothing is in the 2-sided tray, open the back cover.
- Pull the blue tabs on the left and right toward you to release the fuser cover.
- Gently pull the jammed paper out of the back with both hands.
- Close the fuser cover, then close the back cover until it locks.
- Push the 2-sided tray firmly in at the back and the paper tray firmly in at the front.
If the green envelope levers inside the back cover are down, Brother says to lift them to their original position before pulling the blue tabs.
If you print on envelopes, move them back to the envelope position before closing the back cover.
The jam message stays after the paper is gone
A jam message that will not clear usually means a cover is not fully closed or a tray is not seated.
Brother’s Cover is Open message says to check for paper jammed behind the back cover and then close the fuser cover.
Brother’s 2-sided Disabled message says to close the back cover until it locks and seat the 2-sided tray firmly.
If the machine shows Cannot Print ## after that, Brother says to hold the power button to switch it off, wait a few minutes, and switch it on again.
Stop paper feeding badly before it jams
Brother’s printing-problems guide lists fixes for paper that does not feed from the tray.
| Symptom | What Brother says to try |
|---|---|
| Paper is curled | Straighten or flatten it |
| Stack feeds badly | Remove it, turn it over and reload it, or fan it and reload it |
| Tray is too full | Reduce the number of sheets |
| Paper still will not pick up | Clean the paper pick-up rollers |
| MP tray model feeding from the wrong source | Make sure MP Tray is not selected as the paper source in the driver |
For jam prevention, Brother’s Paper Jams topic says to remove the remaining paper from the tray, fan and straighten the stack whenever you add new paper.
Paper size and type mismatches
A mismatch between the driver and the tray can stop a job even when nothing is stuck.
| Message | Brother’s action |
|---|---|
| No Paper T1 | Refill the tray and set the guides to the correct size; do not overfill |
| Size Mismatch | Load the correct size and set the tray size |
| Size Error | Change the driver or tray setting so they match |
| Media Mismatch | Load the correct paper type or change the Paper Type setting |
| Size Error DX | Use a size suitable for automatic 2-sided printing |
Brother lists Letter, Legal, Mexico Legal, India Legal and Folio as suitable sizes for 2-sided printing on the DCP-L2640DW series.
If the printer is also not responding
If clearing the jam does not get the machine printing again, our guides on a Brother printer that will not print and a Brother printer that will not turn on cover the next checks.
When to contact Brother
Brother says most errors and routine maintenance can be handled by the user.
If a message persists, contact Brother Customer Service or your local Brother dealer.
In the USA, Brother lists 1-877-BROTHER (1-877-276-8437), and FAQs at support.brother.com/faqs.
Sources
Brother online user’s guides: Error and Maintenance Messages (HL-L2460DW), Paper jammed in the 2-sided tray (HL-L2460DW), Error and Maintenance Messages (DCP-L2640DW series) and Printing Problems (MFC-L9610CDN).