How To Fix Brother Printer No Paper Or No Paper Fed (2026)
A Brother printer that says No Paper or No Paper Fed, even though the tray is full, is usually failing to pick up the sheet rather than running out of it.
Brother’s support pages list a handful of causes, and the cure for most of them takes a minute.
This guide covers both laser and inkjet models, with the roller cleaning steps Brother gives for each.
Quick answer: the causes Brother lists
| Cause | Fix |
|---|---|
| Tray empty or paper loaded badly | Refill or reload, set the guides, do not overfill |
| Paper not centered in the manual feed slot | Reinsert it centered, then press Start |
| Jam Clear Cover or Jam Clear Flap not closed | Close it evenly at both ends |
| Paper tray not fully inserted | Remove it and push it in until it locks |
| Paper dust on the pick-up rollers | Clean the rollers with a damp lint-free cloth |
| Paper outside Brother’s specifications | Use paper that meets them |
Step 1: reload the paper properly
Brother’s first fix on every model is to take the paper out and put it back.
| Message | What Brother says it means |
|---|---|
| No Paper | The tray is empty or the paper is loaded incorrectly |
| No Paper Tray1 or Tray2 | The machine failed to feed from the tray shown on the screen |
| No Paper MP Tray | The MP tray is empty or loaded incorrectly, on some models only |
| No Paper Fed | Inkjet models: paper not loaded, jammed, dusty rollers, or a cover or tray not seated |
Look at the screen first, because the tray name tells you where to look.
- Pull the paper tray out of the machine.
- Remove the paper from the tray.
- Reload it and move the paper guides to match the paper size.
- Do not overfill the tray, because Brother says not to.
- Push the tray back in firmly.
On laser models with more than one tray, refill the tray named on the screen, such as Tray1, Tray2 or MP Tray.
Step 2: check the manual feed slot on inkjet models
On inkjet models with a manual feed slot, Brother says the paper must be centered in the slot.
- Remove the paper from the slot.
- Insert it again, centered.
- Press Black Start (Mono Start) or Color Start (Colour Start).
On some inkjet models, Brother adds that a photo bypass tray left in the wrong position triggers the message when you use cut sheet paper, so return it to the Normal position after printing photos.
Step 3: close the cover and seat the tray
Two small mechanical checks cause a lot of false alarms.
- Make sure the Jam Clear Cover is closed evenly at both ends.
- Remove the paper tray completely and reinstall it until it locks into place, then press OK.
If paper really is stuck inside, use our Brother paper jam guide instead.
Step 4: clean the paper pick-up rollers
Paper dust on the rollers is one of the most common reasons for No Paper Fed, and Brother lists it on every page.
The steps differ between laser and inkjet models, so use the right set.
| Step | Laser (MFC-L2700DW page) | Inkjet (MFC-J6520DW page) |
|---|---|---|
| Power | No power step listed | Unplug the machine first |
| Tray | Pull the tray out and remove the paper | Pull the tray all the way out |
| Cloth | Lint-free cloth wrung out in lukewarm water | Soft lint-free cloth dampened with water |
| Wipe | The separator pad, then the two pick-up rollers | The base pad, then the rollers under the Jam Clear Flap |
| Finish | Reload the paper and reinsert the tray | Dry with a clean cloth, push the tray in, plug the machine in |
On the inkjet page, Brother says to turn the rollers slowly so the whole surface is cleaned, and to dry them afterward.
Use only water on the cloth, because Brother’s pages do not mention any cleaning solution.
If the machine pulls several sheets at once
When the printer feeds more than one sheet, or only a few sheets remain, Brother’s inkjet page adds one more step.
- Wipe the base pad with a soft lint-free cloth dampened with water.
- Dry it with a clean, dry, lint-free cloth.
- Clean the rollers as above, then reinsert the tray.
If your machine has a second tray and feeding fails from it, Brother gives a matching procedure: unplug the machine, pull tray 2 out, and clean its pick-up rollers.
If it happens during two-sided printing
Brother’s MFC-J650DW page says that frequent errors during 2-sided printing or copying can mean the feed rollers are stained with ink.
- Unplug the machine and pull the paper tray all the way out.
- Wipe the front of the paper feed rollers with a damp lint-free cloth, then dry them.
- Lift the Jam Clear flap and clean the back of the rollers the same way.
- Reinsert the tray and reconnect the power.
Brother says not to use the machine until the rollers are completely dry.
Our Brother double-sided printing guide explains how to turn duplex printing on.
After you fix it
On inkjet models Brother says to press Black Start (Mono Start) or Color Start (Colour Start) once the paper is back in place.
On models that show an OK prompt after you reseat the tray, press OK so the machine resumes.
If the message keeps coming back after all of these steps, Brother’s pages send you to its manuals, other FAQs or Contact Us.
Check the paper itself
Brother’s laser page lists paper that does not meet its specifications as a cause, so use paper recommended for your model.
Related Brother and printer guides
- Brother Toner Low and Replace Toner messages
- Brother faded print, streaks and lines
- Brother printer offline on Windows or Mac
- Canon PIXMA paper jam