How To Fix A Brother Printer Cannot Detect Ink Error (2026)
When a Brother inkjet printer shows “Cannot Detect” and refuses to print, the machine is saying it cannot read one of the ink cartridges.
Brother’s support pages tie the message to a short list of causes, and most of them come down to how the cartridge was installed.
This guide follows those Brother pages, starting with the quickest fix and moving to the less common causes.
Quick answer: what to try first
| Step | What Brother says |
|---|---|
| 1 | Remove the cartridge and reinstall it slowly and firmly until it locks into place |
| 2 | Make sure the machine is turned on while you reinstall |
| 3 | Do not reinstall a used cartridge; install a new one |
| 4 | Check the cartridge model number matches your machine |
| 5 | If the message stays, contact Brother Customer Service |
What the Cannot Detect message means
Brother’s FAQ for the MFC-J995DW describes the symptom as “No Ink Cartridge” or “Cannot Detect” appearing after you install a new cartridge, with printing blocked.
The cause it gives is a replacement cartridge that is not seated correctly in its slot, so the machine cannot detect it.
Brother lists the same message on many inkjet models, so the wording below applies to the MFC and DCP families covered by its pages.
Causes Brother lists and the fix for each
| Cause | Brother’s fix |
|---|---|
| New cartridge installed too quickly | Remove it and reinstall slowly and firmly until it locks |
| Cartridge not seated correctly | Same reseat as above |
| A used cartridge was reinstalled | Remove it and install a new cartridge |
| Non-genuine Brother ink | Try a new cartridge; if the error stays, contact Brother |
| Wrong Brother cartridge model | Check the model number and install the correct one |
| Air bubble in a new cartridge | Replace with a new genuine cartridge and turn it so the ink port faces down before installing |
The air-bubble and used-cartridge rows come from the MFC-J1010DW page, so not every model’s page lists all six causes.
Reseat the cartridge
On the MFC-J995DW, Brother gives these steps for a cartridge the machine cannot detect.
- Remove the ink cartridge from the machine.
- Insert it in the direction shown by the arrow on its label.
- Press the area marked “PUSH” gently until the cartridge locks into place.
- Check that it locked in before you close the cover.
Brother’s wording is to push slowly and firmly, not to force it.
Reseat every cartridge on lever-style models
Brother’s page for the MFC-J430W and related older models has you take out all four cartridges and put them back one at a time.
- Open the ink cartridge cover door.
- Push the four colored levers down and remove the ink cartridges.
- Make sure the machine is turned on, because Brother says a powered-off machine cannot detect that cartridges are installed.
- Match each cartridge to the lever of the same color.
- Insert each cartridge slowly, in the direction of the arrow on its label, until it clicks into place, then do the next one.
- Close the ink cartridge cover after all four are in.
Your model’s own screen and cover layout may differ from this older design.
Answer the “Did You Change” prompt
If you replaced a cartridge, Brother says the screen may ask whether it is new, for example “Did You Change Black?”
| Cartridge | Choose |
|---|---|
| Brand-new cartridge | Yes |
| Cartridge that is not brand new | No |
Answer for each cartridge you changed, since the machine uses the answer to track ink.
Avoid air bubbles in a new cartridge
Brother’s pages for older models link air pockets to the way the protective cap is removed.
- Do not hold the cartridge upside down when you remove the protective cap.
- Hold it with the cap facing sideways instead.
- Twist the green knob to pressurize the cartridge before removing the cap, because skipping this can also create air pockets.
Those pages describe an orange cap on some models and a yellow cap on others, so follow the color on your cartridge.
Used, wrong or non-genuine cartridges
Brother says the machine may or may not detect a non-genuine cartridge, so try a new one if you are using third-party ink.
It also tells you to check the model number on the cartridge against your machine, and it points to its Consumables and Accessories section for compatible cartridge numbers.
A used cartridge that was taken out and put back should be swapped for a new one rather than forced in.
Brother recommends genuine supplies and warns that third-party or refilled ink can cause malfunctions that its limited warranty does not cover.
If cartridges went in the wrong slots
If you installed a cartridge in the wrong position and mixed up colors, Brother says to correct the installation and then clean the print head several times.
The page does not give the cleaning procedure, so use your machine’s cleaning function or the Manuals section for your model.
If prints come out faded afterward, see our guide on Brother print quality problems.
Models on the Brother pages used here
| Brother page | Models listed |
|---|---|
| Cannot Detect (J1010DW) | MFC-J1010DW, MFC-J1170DW |
| After replacing a cartridge | MFC-J995DW(XL) plus related J-series models such as MFC-J4335DW and MFC-J5945DW |
| Clear the message (lever models) | MFC-J280W, J425W, J430W, J435W, J625DW, J825DW and others |
| Cannot Detect (J4335DW) | MFC-J4335DW, MFC-J4345DWXL, MFC-J4535DW |
If your model is not named, search Brother’s support site for “Cannot Detect” with your model number.
When to contact Brother
Brother’s pages do not set a specific threshold, and they send you to the Contact Us section when the steps do not clear the message.
Before you call, note whether you are using genuine Brother cartridges, because several of the pages treat that as a first question.
If the printer instead reports a drum or toner message, those belong to laser models, so use our Brother drum error guide or the Brother toner message guide.
If the printer shows offline once the ink is fixed, try our Brother printer offline guide.
If one color is empty and you need to print anyway, see how to print with only color ink when black is empty.