How To Fix A Brother Printer Not Scanning To Computer (2026)

When a Brother printer prints fine but will not scan to your computer, the cause is usually the connection, the scanner driver settings or a firewall.

Brother has separate troubleshooting pages for the Scan key, for scanning from the computer, and for the ControlCenter CC errors.

This guide pulls the steps from those pages into one order, with Windows first and macOS after.

Quick answer: scan problem to first fix

ProblemFirst fix from Brother
Scan key does nothing on a network machine (Windows)Make sure ControlCenter is running, then check the Scan To Button settings
Computer is missing from the machine’s Scan to menuRegister the computer under the Scan To Button tab in scanner properties
Prints over the network but will not scanCheck the scanner driver, the IP address and the firewall ports
Error CC3-202, CC4-202, CC3-205 or CC4-205Check the connection, the stisvc service and security software
iPrint&Scan will not scanSet iPrint&Scan as the program for each scan event

Check the connection first

Brother’s scan guides start by confirming that the machine can still talk to the computer.

  • USB: connect the cable firmly, remove any USB hub, and use a cable no longer than 2 meters.
  • Wired network: check the cable between the machine and the router or access point.
  • Wireless: confirm the machine is connected to the wireless network.

Brother also says to check that the machine’s display shows the date and time and no error message.

If printing over the network fails too, fix that first, starting with our guide to a Brother printer paper jam only if a jam is showing, or the Brother printer won’t print checklist.

Make sure ControlCenter is running

On Windows, the Scan key over a network depends on ControlCenter running on the computer.

  1. Look for ControlCenter in the system tray near the clock.
  2. If it is not there, open Start, then Brother, then Brother Utilities.
  3. Click Scan in the left navigation bar, then click ControlCenter.
  4. Try the Scan key on the machine again.

Confirm the scanner driver and port

Brother says to check that the scanner driver is installed and that it points at your machine.

Windows versionWhat Brother says to do
Windows 11In your scanning app, select the Brother TWAIN or WIA driver as the source, and install the Full Driver and Software Package or the Scanner Driver from Downloads if it is missing
Windows 10 or earlierOpen Scanners and Cameras, confirm your Brother icon appears, and install the Full Driver and Software Package if it does not
Windows 7, 8 and 10 network settingIn Scanner Properties, open the Network Setting tab and specify the machine by address or by name

You can find the IP address or node name by printing the Network Configuration Report from the machine.

If Boot Method (IP Config) on that report says AUTO, Brother says to change it to STATIC so the address stops changing.

Register the computer for the Scan key

If your computer does not appear as a destination on the machine’s display, Brother says it has not been set up under Scan To Button.

  1. Open the scanner properties for your Brother machine.
  2. Click the Scan To Button tab.
  3. Check the box to register your computer with the Scan To functions at the machine.
  4. Enter a Display Name, which will appear in the machine’s Scan to menu.
  5. Click OK.

On Windows 7, 8 and 10 the display name can be up to 15 characters, and your computer name is the default.

Brother also offers an optional 4-digit PIN, so the machine asks for it before it scans and sends.

Check the firewall

Brother says a firewall can block the connection that network scanning needs.

Its test is to turn the firewall off briefly, try scanning, and turn it back on when you finish.

Brother warns that you should make sure the change suits your network first, and that it accepts no responsibility for what disabling a firewall causes.

If scanning works with the firewall off, the better fix is to keep the firewall on and allow these ports.

PortUse
UDP 54925Network scanning, and the only one Brother lists for macOS
UDP 137Added if problems persist
UDP 161Added if problems persist

Error CC3-202, CC4-202, CC3-205 and CC4-205

Brother does not name a single cause for these ControlCenter errors, so it gives a sequence to follow.

  1. Check the USB, wired or wireless connection.
  2. Check that the machine’s display shows no error.
  3. Temporarily disable firewall or security software.
  4. Press Ctrl, Alt and Del, open Task Manager, then the Services tab, and check that stisvc is Running; if it is Stopped, right-click it and click Start Service.
  5. Try scanning from another program such as MS Paint.
  6. Restart the computer.
  7. Uninstall the Brother software, then reinstall the Full Driver and Software Package from Downloads.

Brother lists these steps for models including the ADS-1000W, ADS-2500W and MFC-7240, so check your own model’s page.

If you scan with iPrint&Scan on Windows

Brother says to install the latest iPrint&Scan and then set it as the program for the scan events.

  1. Open Brother Utilities and select your model.
  2. Click Scan, then Scanners and Cameras.
  3. Click your machine’s icon, then Properties, and allow User Account Control if it asks.
  4. Open the Events tab and pick one event, such as Scan/Image Button.
  5. In Start this program, choose Brother iPrint&Scan and click OK.
  6. Repeat for the remaining events.

If you scan on a Mac

For iPrint&Scan on a Mac, Brother lists three extra points.

  • On macOS 15 or later, go to System Settings, then Privacy and Security, then Local Network, and enable Brother iPrint&Scan.
  • To use the machine’s Scan button, download the iPrint&Scan Push Scan Tool and click Allow when WorkflowAppControl and NETserver appear.
  • If a firewall is active, open UDP 54925.

For other Macs, Brother says to use the Device Selector to set up scanning from the control panel.

Reinstall the software and check firmware

If nothing above works, uninstall the Brother drivers and reinstall them, then try another computer on the same network.

Brother says that if other computers can scan, the problem is specific to the first computer.

It also tells you to make sure the machine has the latest firmware.

When to contact Brother

If scanning still fails on a second computer, use the Contact Us section on Brother’s support site for your model.

Official sources: Network scanning does not work when pressing the Scan key, Cannot scan via network (Windows), Error CC3-202 and CC4-202 and Cannot scan with Brother iPrint&Scan.

Leave a Reply

Your email address will not be published. Required fields are marked *