How To Fix Brother Toner Low And Replace Toner Messages (2026)

A Brother laser printer that still says Toner Low or Replace Toner is usually reacting to the cartridge, not broken.

The fix depends on whether the message is a normal warning or one that stays on after you fitted a new cartridge.

This guide follows the steps in Brother’s own support articles for each case.

Quick answer: what each toner message means

What you seeWhat it meansWhat Brother says to do
Toner Low or Prepare New Toner CartridgeThe cartridge is near the end of its expected life but not finishedKeep printing while quality is acceptable and get a new cartridge ready
Replace TonerThe cartridge needs replacingInstall a new toner cartridge only
Toner Low or Replace Toner after a new cartridgeWrong part, used cartridge, poor seating or a dirty corona wireWork through the five checks below
Toner LED on or flashingSame toner warning on models with LED indicatorsUse the same checks

Toner cartridge versus drum unit

Most Brother laser printers use two separate consumables, a toner cartridge and a drum unit.

Brother says to replace only the toner cartridge when a toner message appears, and to leave the drum unit alone.

The two parts look similar, so a wrong swap is one of the first things to rule out.

If your message mentions the drum instead, read our guide to Brother Replace Drum and Drum Error messages.

Toner Low and Prepare New Toner Cartridge

Toner Low and Prepare New Toner Cartridge are warnings, not stop errors.

Brother says the cartridge is near the end of its life but has not reached the end.

You can keep using it while print quality stays acceptable.

On color models the message names the cartridge, using BK for black, C for cyan, M for magenta and Y for yellow.

Replace Toner

Replace Toner means the cartridge now needs replacing.

Brother recommends keeping a new genuine Brother toner cartridge on hand so you are ready when this appears.

The order number for your model is listed on Brother’s consumables page for that product.

The message stays after you install a new cartridge

This is the case Brother covers in its dedicated troubleshooting article, and it lists the same checks for many DCP, HL and MFC models.

  1. Confirm that you replaced the toner cartridge and not the drum unit.
  2. Confirm that the new cartridge is brand new and unused.
  3. Reinstall the toner cartridge and check that both a toner cartridge and a drum unit are fitted.
  4. Clean the corona wire.
  5. Update the firmware, where Brother lists a firmware tool for your model.

If the warning is still there, Brother says to contact its customer service.

Why a used cartridge keeps the warning on

Brother says the machine only resets its toner status when it sees a new, unused cartridge.

A cartridge moved from another printer, or a partly used one, can leave the warning on because the machine cannot track toner use correctly.

On color models, Brother adds a useful check: if the same color message returns, reinstall that cartridge, and if the message now names a different color, replace that color instead.

Clean the corona wire

Brother lists a dirty corona wire as a possible cause of a toner message that will not clear.

The steps below follow Brother’s guide for a color model, the HL-L8360CDW.

  1. Press the front cover release button and open the front cover.
  2. Hold the green handle and pull the drum unit out until it stops.
  3. Push each toner cartridge handle away from you to unlock it, then lift the cartridge out of the drum unit.
  4. Slide the green tab left and right several times for each corona wire.
  5. Return the green tab to its home position, flush with the left side of the drum.
  6. Put each cartridge back by matching its color to the colored label on the drum unit.
  7. Push the drum unit back in until it locks and close the front cover.

Brother warns that leaving the tab out of its home position can cause poor print quality, and on a single-color model it can cause a vertical stripe on pages.

Single-color and color models differ

DetailSingle-color example (HL-2140)Color example (HL-L8360CDW)
What comes outDrum and toner assembly together, then the cartridge is separatedDrum unit first, then each cartridge
Unlock methodPush down the green lock leverPush the cartridge handle away from you
Corona wire tabSlide right to left and back, then return homeSlide left and right, then return flush with the left side
Before closing the coverWait for the Ready LEDWait for Ready Mode on the display

Because the procedure varies, open the replacement guide for your exact model on Brother’s support site.

Handling a new cartridge correctly

Brother’s replacement guides repeat a few points that affect how long the cartridge lasts.

  • Unpack the new cartridge only when you are ready to install it, because a long time out of the pack shortens toner life.
  • On the HL-2140 guide, rock the cartridge gently from side to side five or six times before fitting it.
  • Press the cartridge in until it clicks or locks, since one that is not seated can separate from the drum unit.
  • Do not switch the printer off or open the front cover until it shows Ready.
  • Never use spray cleaner inside or outside the machine, because Brother warns of fire or electric shock.

When the warning seems to come too early

Brother explains that the cartridge shipped with a printer may be a starter, standard or high-yield cartridge, and yield varies by model and country.

FactorEffect on page count
Paper sizeChanges how many pages a cartridge prints
Pages per jobChanges how many pages a cartridge prints
Coverage per pageHeavy coverage uses far more toner
Font size and contentLarge fonts, graphics, charts and solid black areas shorten cartridge life

Brother’s baseline is a letter-size page with 4 to 5 percent coverage, such as a short memo of about 1,500 characters.

Check for a firmware update

For the MFC-7360N, Brother’s article tells you to open the Downloads section for your model and look for the Firmware Update Tool.

If the tool is listed, compare its version with the firmware on your machine and update when yours is older.

If it is not listed, Brother says to contact customer service.

Genuine toner and warranty

Brother says each printer is designed around its own toner formulation and that genuine supplies are built to work together.

It also says not every non-genuine product causes problems, but some reduce print quality or cause the machine to malfunction.

Brother’s limited warranty does not cover problems or damage caused by third-party drums, cartridges or toner, and Brother advises against refilling cartridges.

When to contact Brother

If the message survives a new genuine cartridge, correct seating and a clean corona wire, Brother points you to its customer service through the Contact Us section.

If the printer will not print at all for another reason, see our Brother printer won’t print checklist or the guide to a Brother paper jam error.

Official sources: Brother toner message after replacement, Toner Low or Prepare New Toner Cartridge and Replace the toner cartridge.

Leave a Reply

Your email address will not be published. Required fields are marked *