How To Fix Brother Laser Faded Print, Streaks And Lines (2026)

Faded print, streaks and stray lines on a Brother laser printer each point to a different part, so matching the symptom first saves you from replacing the wrong one.

Brother’s own print quality guides list a short set of checks and then a fix for every symptom.

This guide follows those guides, which are written for Brother color laser models such as the HL-L3210CW series, the MFC-L9670CDN and the HL-3040CN.

Quick answer: symptom to first fix

SymptomFirst thing Brother says to try
Colors light or faint across the pageTurn Toner Save off, calibrate, and gently shake the toner cartridges
Vertical white streaks or bandsWipe the LED head windows with a dry, lint-free cloth
Vertical colored streaksClean the corona wires by sliding the green tab
Horizontal colored linesFind the color responsible and replace that toner cartridge
White spotsMatch the driver media type to your paper and check humidity and heat
GhostingCheck for low humidity or temperature and the media type
Toner smears easilySelect Improve Toner Fixing in the printer driver

Start with the basic checks

Brother tells you to print a test page first.

If the test page looks good, the printer is probably not the problem, so check the cable connections and try a different document.

Use print media that meets Brother’s paper specifications, and make sure the media type in the driver matches the paper you loaded.

Check that the toner cartridges and drum unit are installed correctly.

Brother also warns that non-genuine supplies may affect print quality, hardware performance and reliability.

Faded or faint print

When colors are light across the whole page, Brother lists these fixes in this order.

  1. Calibrate the color output from the printer’s LCD.
  2. Turn Toner Save off, on the LCD or in the printer driver.
  3. Make sure the media type in the driver matches your paper.
  4. Gently shake all four toner cartridges.
  5. Wipe the windows of all four LED heads with a dry, soft, lint-free cloth.

On the HL-3040CN guide, Brother also lists uneven or faded print as fixable by fully opening the top cover and closing it again.

Vertical white streaks and bands

Brother’s guide points to dirty LED heads or foreign material inside the machine.

Wipe the LED head windows with a dry, lint-free cloth.

Look inside for a torn piece of paper, a sticky note or dust around the toner cartridges and drum unit.

The older HL-3040CN guide adds dust or glue on the drum surface and a damaged toner cartridge as causes.

Vertical colored streaks and horizontal lines

SymptomBrother’s fixes, in order
Vertical colored streaks or bandsClean all four corona wires, return each green tab to home, replace the toner of the matching color, then install a new drum unit
Horizontal colored linesIdentify the color and replace that toner cartridge, then install a new drum unit if needed
Blank page or missing colorsIdentify the color, replace that toner cartridge, then a new drum unit
All one color (HL-3040CN)A damaged drum unit, so replace that color’s drum

Brother says to identify the problem color using the FAQs and Troubleshooting page for your model at support.brother.com.

The HL-3040CN guide uses a printable color chart that you compare with your printout to find the color responsible.

How to clean the corona wires

Brother’s steps for a color model are short.

  1. Open the front cover and pull the drum unit out by its green handle.
  2. Unlock and lift out each toner cartridge.
  3. Slide the green tab left and right several times for each corona wire.
  4. Return each green tab to its home position, flush with the left side of the drum.
  5. Refit the cartridges to their matching colors and push the drum unit back in until it locks.

If the toner message is also stuck, our guide to Brother Replace Drum and Drum Error messages covers the drum side.

Spots, stains and scatter

SymptomWhat Brother says
White spotsCheck the media type, check for high humidity or heat, and clean the drum unit if it continues after a few pages because label glue may be on it
Colored spots at 94 mm (3.7 in.)Clean the drum unit if it persists, then install a new drum unit
Colored spots at 29 mm (1.1 in.)Identify the color and install a new toner cartridge
Toner scatter or stainCheck humidity and heat, replace the toner of the affected color, then a new drum unit

The HL-3040CN guide gives the operating range as 10 to 32.5 degrees C (50 to 90.5 degrees F) and 20 to 80 percent humidity without condensation.

Wrong colors, color offset and uneven density

For colors that are not as expected, Brother says to calibrate and run color registration from the LCD.

It also says to turn Toner Save off, select Enhance Black Printing for weak blacks, and clear Improve Gray Color in the driver.

For color offset, put the printer on a solid, level surface and run color registration, then install a new drum unit or belt unit if the problem continues.

For uneven density across the page, calibrate and clear Improve Gray Color before replacing the toner or drum of the affected color.

Smearing, thin lines and fine detail

  • Toner that smears easily: select Improve Toner Fixing in the driver, and if needed set the media type to a thick setting, or Env. Thick for envelopes.
  • Missing thin lines in images: turn Toner Save off, change the print resolution, and in the Windows driver select Improve Pattern Printing on the Basic tab.
  • Characters cut off at the edges: adjust the print margins in the application and reprint.

Wrinkles, curl and ghosting

SymptomWhat Brother says
Wrinkled printoutCheck paper type and quality, close the back cover correctly, and keep the two gray levers up
Curled or wavy imageSelect Reduce Paper Curl, then Plain Paper, turn the paper stack over, and store paper away from heat and humidity
GhostingLow humidity or temperature can cause it, so check the media type and levers, then install a new drum unit
Envelope creasesPull the envelope levers inside the back cover down, then return the gray levers to the up position afterward

Brother adds that you can open the back cover so pages leave face up when curl persists.

Genuine supplies and warranty

Brother recommends genuine toner and drum units because each printer is tuned for them.

Its limited warranty does not cover problems caused by third-party drums, cartridges or toner.

When to contact Brother

If a symptom survives the fixes for it, including a new cartridge and drum unit, use the Contact Us section on Brother’s support site for your model.

If pages will not print at all, read our Brother printer won’t print checklist instead, and for jams see Brother paper jam fixes.

Official sources: Improve the Print Quality (HL-L3210CW series), Print quality problems (HL-3040CN) and Improve the Print Quality (MFC-L9670CDN).

Leave a Reply

Your email address will not be published. Required fields are marked *