How To Reconnect A Canon PIXMA Printer To Wi-Fi (2026)

When a Canon PIXMA printer drops off your Wi-Fi, the cause is almost always a mismatch between the printer and the router rather than a broken printer.

Canon publishes a numbered checklist for this problem, plus separate pages for a replaced router and for Wireless Direct.

This guide puts those pages together in the order that saves the most time.

Quick answer: find your situation

SituationCanon’s fix
Printer worked yesterday and now will not connectPower-cycle the printer, router and computer, then check the Wi-Fi icon or lamp
You replaced the router or changed its settingsRedo the printer’s network setup
You turned on MAC or IP address filteringRegister the computer and printer on the router
The Wi-Fi icon or lamp is offTurn wireless communication back on
No router availableUse Wireless Direct

Turn everything off and on

Canon’s first check is to confirm that the printer, the router and your device are switched on, and to cycle the power if they already are.

It adds that router settings such as the key update interval, the DHCP interval or an energy-saving mode can cause dropouts.

Canon also says the router firmware may need updating, and that its maker is the one to ask.

After a network change, wait for an IP address

Canon says a computer that just joined a changed network may need time to receive an IP address.

Wait a short while or restart the computer, confirm it has a valid IP address, and then search for the printer again.

Confirm the computer is online

Open a web page on the computer you are printing from.

If the page will not load, the computer is the one that has lost the router, so fix that connection before blaming the printer.

Check that Wi-Fi is switched on at the printer

On a model with a screen, press OK and look for the Wi-Fi icon on the LCD, because Canon says a missing icon means wireless is disabled.

Printers without a screen use lamps, and the steps differ by model.

Printer typeHow Canon says to check or enable Wi-Fi
Models with an LCD, such as the TS5300 seriesPress OK, look for the Wi-Fi icon, and turn on wireless communication if it is missing
E460 series, no LCDCheck that the Wi-Fi lamp is lit, otherwise hold Stop until the Alarm lamp flashes 18 times, release it, then press Color

Other lamp-only models may use different buttons, so check the manual for your exact series.

Make the printer match the router

The printer’s network name and password must be the same as the router’s.

Canon says to use the router’s 2.4 GHz band and to match the printer to that band’s network name.

You can print the printer’s network settings to see which name it is using.

After replacing the router or changing its settings

Canon’s page for this case says to redo the printer’s network setup.

  1. On Windows, run setup again from the Setup CD-ROM or Canon’s setup web page.
  2. On a Mac, use the setup web page.
  3. If the problem continues, run Canon’s IJ Network Device Setup Utility to diagnose and repair the network status.

If you use MAC filtering or a changed encryption key

Router settingWhat to confirm
MAC or IP address filteringThe computer, other network devices and the printer are all registered
WPA, WPA2 or WEP keyThe key on the computer, devices and printer matches the router’s
WEP specificallyKey length, key format, key ID and authentication method also match
Changed encryption typeThe type on the computer and router matches the printer’s setting

Check Wi-Fi channels

Canon says the computer must use the same channel as the router.

Some computers restrict which channels they can use, so if the router sits on a channel the computer cannot use, change the router’s channel.

Your computer’s manual lists which channels it supports.

Reduce distance and interference

  • Move the printer closer to the router, because some routers have internal antennas.
  • Remove walls, floors and metal or concrete materials between them if you can.
  • Put the printer in the same room as the computer if a wall blocks the signal.
  • Keep the router away from microwave ovens.

On models with an LCD, Canon says you can read the signal strength on the screen.

Allow Canon software through the firewall

Canon says security software may block its tools, so set the firewall to always allow access when a warning appears.

It also says programs that switch network environments may turn on a firewall by default, so check those too.

Use Wireless Direct when there is no router

Wireless Direct connects a device to the printer without a router.

LimitWhat Canon says
InternetThe printer has no internet access, so web services are unavailable
DevicesUp to five at once, and a sixth causes an error
Your phoneA device may lose its internet connection or switch to mobile data

On the TS5300 series, enable it under Device settings, LAN settings, Wireless Direct, Advanced mode.

Then pick the printer’s Wireless Direct name on your device and enter the password shown on the printer or in its printed network settings.

Keep the printer close to the device while you connect, and disconnect some devices first if five are already using it.

If it is connected but will not print or scan

  1. Confirm the computer is connected to the router.
  2. On Windows, install the Canon printer driver if it is missing, using the download on Canon’s support page for your model.
  3. Check that the router is not limiting which computers may use it, using the router manual or its maker.

Canon’s page says the computer’s MAC or IP address is what you register when a router restricts access.

If a phone or tablet cannot find the printer

Our guide to fixing no printers found on an iPhone covers the phone side.

If Windows shows the printer but refuses to print, see our Canon printer offline guide.

Router changes are also covered in our guide to printers that stop after a router change.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *