How To Reconnect An HP Printer To Wi-Fi (2026)

When an HP printer will not join your Wi-Fi, the fastest route is usually to put it back into Wi-Fi setup mode and connect it again.

HP documents several ways to do that, depending on whether your printer has a touchscreen, a WPS button or neither.

This guide lays out each method in HP’s order and says when to use it.

Quick answer: pick the right method

Your situationMethod to use
Setting up a new printer or an app cannot find itRestore Wi-Fi setup mode, then use the HP app
You changed your router or internet providerWireless Setup Wizard or WPS
Printer has a touchscreenWireless Setup Wizard on the control panel
Printer has no touchscreenHP=Setup network and the printer web page, or WPS
Printer was set up with a USB cableRemove the USB printer, then set it up again in the HP app
You are on a hotel or school networkWi-Fi Direct instead of the shared network

Check these basics first

  • Keep the printer close to the router while you connect it.
  • If you use a VPN on the computer, disconnect it during setup.
  • Turn on Bluetooth on your computer or phone, because HP says the HP app uses it to detect the printer during setup.
  • Check with your router maker if wireless isolation is on, because HP says it can make a printer appear offline.

HP adds that a guest network, such as those in hotels or college campuses, might not allow a device to reach the printer.

Restore Wi-Fi setup mode

Setup mode lets the printer accept a new Wi-Fi connection from the HP app.

While it is active, the Wireless icon or light blinks until a connection is made or two hours pass.

Printer typeHow to restore setup mode
Touchscreen or menuOpen the Wireless or Setup menu, choose Network setup or Settings, then choose Restore Network Settings
No touchscreen or menuPress and hold the Wireless and Cancel buttons for five seconds or until the Wireless light blinks

If the light does not blink, HP points to a separate model-specific page on restoring Wi-Fi setup mode.

Finish setup in the HP app

  1. Open the HP app and create an account or sign in.
  2. Download the app from 123.hp.com or your app store if you do not have it.
  3. Within two hours of restoring setup mode, follow the guided steps to add the printer and set up the wireless connection.

Use the Wireless Setup Wizard on a touchscreen printer

  1. Place the printer near the router.
  2. Open the Setup, Network or Wireless settings menu and choose Wireless Setup Wizard.
  3. Select your network name and enter the password.

If the wizard is not listed, HP says to choose Wi-Fi Protected Setup (WPS), then Push Button, and follow the prompts.

Use the printer web page if there is no touchscreen

This method connects your device to a temporary network that the printer creates.

  1. In your device’s Wi-Fi list, join the network named HP=Setup followed by your printer name.
  2. If it is missing, restore setup mode by holding Wireless and Cancel until the Power button blinks and the Wireless light blinks.
  3. Open a browser and enter 192.168.223.1.
  4. If a connection-not-private warning appears, click Show Advanced and then proceed.
  5. Enter the PIN from the label inside the cartridge access area.
  6. Click Network, then Wireless, then Wireless Setup Wizard, then Next.
  7. Pick your Wi-Fi network and enter its password.

When the connection works, the Wireless light stops blinking and you can add the printer to the HP app.

Connect with the WPS button

WPS pairs the printer with the router without typing a password.

PrinterStart WPS mode on the printer
Most printers without a touchscreenPress and hold the Wi-Fi button for 5 seconds until the light flashes
HP DeskJet 6000 and 6400, ENVY 6000 and 6400, TangoHold the Wi-Fi and Power buttons on the back for 3 seconds until the Edge or Wireless light flashes

Within 2 minutes, press and hold the WPS button on the router until the connection starts.

Wait for the wireless light or bar on the printer to stop flashing, which means it is connected.

Switch from a USB setup to Wi-Fi

HP says a printer that was set up over USB must be moved to a network connection before it can print wirelessly.

  1. Turn off the printer and the computer, then unplug the USB cable from both.
  2. Turn both back on and close any setup prompts.
  3. Remove the printer from the HP app: click it, scroll down and click Remove from app, or in HP Smart right-click it and choose Hide Printer twice.
  4. Go to 123.hp.com, find your printer and install the print app.
  5. Run the guided printer setup to connect over Wi-Fi.

Chromebook users should use HP’s separate Chromebook printer setup page instead.

Use Wi-Fi Direct when the network blocks printers

HP recommends Wi-Fi Direct for guest networks, because it connects a phone or computer straight to the printer.

It is a temporary link rather than a replacement for your home network.

If the printer still will not connect

HP’s scanner-connection page lists extra wireless checks that also apply to a printer that is hard to find.

  • Move the printer and your device closer to the router and see whether the signal improves.
  • Open a website to test the internet, and if Wi-Fi is slow or drops out, unplug the router, wait 15 seconds and plug it back in.
  • Touch the control panel or press Power to wake a printer that is asleep, since HP notes an idle printer can show Offline while actually ready.
  • Check that the Wireless light is on, because HP says an off or blinking light means the printer is disconnected from the network.
  • Restart both the printer and your computer or phone to clear error conditions.

Confirm the connection worked

A printer that has joined your network should stop blinking its Wireless light.

You can also print a Network Configuration Report from the HP app, under Printer Reports in Tools, or from the Wireless or Network Settings menu on a touchscreen printer.

On that report, check that the wireless status reads Connected before you try printing again.

Source for these extra checks: HP: Scanner not found or connected.

If the printer connects but shows Offline, see how to fix an HP printer that shows offline.

If your iPhone cannot see it afterwards, read No Printers Found on iPhone.

Sources: HP printer setup (Wi-Fi network) and HP: Change from a USB to a Wi-Fi connection.

Leave a Reply

Your email address will not be published. Required fields are marked *