How To Fix Canon Printer Streaks And Blurry Prints (2026)
White streaks, blurry text and washed-out colors on a Canon PIXMA print usually come from clogged print head nozzles.
Canon’s fix is a fixed ladder of steps, starting with a nozzle check pattern and ending, if nothing works, with replacing the print head or cartridge.
This guide lays out that ladder, including the button paths Canon gives for its G4000 series, and says when to stop.
Quick answer: the cleaning ladder
| Step | Action | Then |
|---|---|---|
| 1 | Print a nozzle check pattern | Look for missing lines or white streaks |
| 2 | Clean the print head | Print the pattern again |
| 3 | Clean the print head a second time | Print the pattern again |
| 4 | Deep print head cleaning | Print the pattern again |
| 5 | Switch off for more than 24 hours, then deep clean again | Print the pattern again |
| 6 | Replace the print head or FINE cartridge | Contact service if still bad |
Before you start
- Check that the ink tanks are not low, because Canon says a low tank can stop the pattern printing correctly.
- On cartridge models, confirm the FINE cartridge is installed correctly and its protective tape is removed.
- If the Alarm lamp is lit or flashing, read the error first.
- Do not rinse or wipe a FINE cartridge.
Canon says cleaning uses ink, so only do it when the pattern shows a problem.
Rule out paper and print settings
Canon’s first check is whether the paper type and print quality settings match the paper you loaded.
It also says paper with only one printable side must be loaded with that side facing down in the cassette.
Printing on the wrong side can give unclear, lower-quality results.
Print a nozzle check pattern
These steps are Canon’s for the G4000 series ink tank printers.
- Make sure the printer is on.
- Load one sheet of A4 or Letter plain paper in the rear tray.
- Choose the matching paper size and Plain paper on the LCD, then press OK.
- Pull out the output tray and open its extension.
- Press Setup, select Maintenance, press OK, then select Nozzle check and press OK.
Other series use similar menus, but check the manual for your model, and you can also print the pattern from the Canon driver on your computer.
Decide whether you need cleaning
Canon says to clean the print head if lines are missing or the pattern shows horizontal white streaks.
If the pattern looks complete, the print head is probably fine and the cause is more likely paper, settings or the original document.
Clean the print head
On the G4000 series, press Setup, select Maintenance, press OK, select Cleaning and press OK.
Canon says the cleaning takes about one minute and that you should not use the printer until it finishes.
Print the nozzle check pattern again afterward, then clean once more if it has not improved.
Deep cleaning
Canon says to use deep cleaning only if two normal cleanings have not helped, because it uses more ink.
| Cleaning type | G4000 series menu path | Time Canon gives |
|---|---|---|
| Cleaning | Setup, Maintenance, Cleaning | About 1 minute |
| Deep cleaning | Setup, Maintenance, Deep cleaning | About 3 minutes |
Print the pattern once more after the deep clean to see the result.
If it still looks wrong, wait 24 hours
Canon’s guidance for several models says to turn the printer off and wait more than 24 hours after an unsuccessful deep clean.
Then run the deep cleaning again and print another pattern.
Canon’s G4000 page also lists system cleaning as a last step before replacement, but warns that it uses a large amount of ink and can damage the printer if ink is low.
If only copies have streaks
When prints look fine but copies are streaky, the print head is not the problem.
| Check | What Canon says |
|---|---|
| Glass | Clean the platen glass and the ADF glass, because a dirty ADF glass causes black streaks on copies |
| Original placement | Place the side to copy facing down on the platen, or facing up in the ADF |
| The original itself | If it is a printout from this printer, its own quality may limit the copy |
For a poor original, Canon suggests printing directly from the printer or reprinting from the computer if you can.
Try a higher print quality on Windows
For blurred or uneven prints, Canon’s maintenance page notes that on Windows a higher print quality setting in the printer driver may help.
Do this alongside the paper type check, because a plain-paper setting on glossy paper can also look streaky.
Match the symptom to the step
| Symptom Canon lists | Where to start |
|---|---|
| Ink does not come out | Nozzle check pattern, then cleaning |
| Blurry or fuzzy prints | Paper settings, then cleaning |
| Inaccurate or bleeding colors | Nozzle check pattern, then cleaning |
| White streaks or lines | Cleaning, then deep cleaning |
| Blank, faint or tinted prints | Canon’s separate print quality page for your model |
When to replace the print head or cartridge
| Printer type | If cleaning fails |
|---|---|
| Ink tank models, such as the G4000 series | Replace the print head |
| FINE cartridge models | Replace the FINE cartridge, then contact a Canon service center if it persists |
Some Canon series offer a Replace Ink in Print Head option to try first, which Canon lists as the step after deep cleaning on that model.
If the problem remains after a replacement FINE cartridge is installed, Canon says to contact a Canon service center for repair.
Always print one more nozzle check pattern after each step, because that pattern is how Canon tells you whether the step worked.
Air in the ink path after long storage
Canon says a tiny amount of air in the tube is normal and does not affect output.
If a printer sits unused for a long time, large bubbles can reach the print head and cause blurred images or blank pages.
Canon recommends printing at least once a week to keep image problems down.
If lines look doubled or misaligned
That is a different fault from clogged nozzles.
Canon says to align the print head, either from the printer or through the driver settings on your computer.
Related guides
If black ink is the problem, see our guide to printing with only color ink when black is empty.
If the printer shows an error code instead, see our Canon error code guide.