How To Fix Brother Replace Drum And Drum Error Messages (2026)
A Brother laser printer that keeps showing a drum message is telling you about the drum unit, the toner seating or the drum counter.
The wording matters, because Replace Drum, Drum End Soon and Drum ! each have a different fix in Brother’s own guides.
This guide explains each message and the steps Brother lists, including how to reset the drum counter after a new drum goes in.
Quick answer: what each drum message means
| Message | What it means | What Brother says to do |
|---|---|---|
| Drum End Soon | Drum unit is nearing the end of its life | Order a replacement before Replace Drum appears |
| Replace Drum | Drum is worn out, or the counter was not reset | Fit a new drum, or reset the counter if one is already fitted |
| Drum ! | Corona wire is dirty, or the drum is not seated | Clean the corona wire, then reseat the parts |
| No Drum Unit | Drum is not installed correctly | Reinstall the toner and drum assembly |
| Cannot Detect | Toner or drum not detected | Take the toner out of the drum, reinsert it, reinstall the assembly |
Drum unit versus toner cartridge
In these Brother laser models the toner cartridge sits inside the drum unit, and the two slide in and out as one assembly.
Several drum-related messages are really about how that assembly is seated rather than about wear.
That is why Brother’s steps often tell you to separate the toner from the drum and put them back together.
Drum End Soon
Drum End Soon means the drum unit is close to the end of its life.
Brother says you can order a new drum unit now so it is ready before Replace Drum appears.
Nothing else needs fixing at this stage.
Replace Drum
Replace Drum has two causes in Brother’s guide.
- The drum unit has reached the end of its life, so you install a new drum unit.
- You already fitted a new drum, but the drum counter was not reset, so you reset the counter.
Do not reset the counter unless you have installed a new drum, because Brother warns that it gives an inaccurate drum life count otherwise.
Reset the drum counter
Brother’s steps differ by model, and the page lists them for the HL-L2400D series.
| Model | Steps from Brother |
|---|---|
| HL-L2400D | Turn the machine on, open the front cover, hold Go for about four seconds until all four LEDs light, release, close the cover, and check that the Drum LED is off |
| HL-L2405W, HL-L2420DW, HL-L2460DW, HL-L2460DWXL, HL-L2865DW | With the cover closed, press OK and the triangle button together, press OK to select Drum, then select Reset |
Other Brother models use different menus, so check the guide for your model at support.brother.com.
Drum !
Drum ! has two causes in Brother’s table.
- The corona wire on the drum unit is dirty, so clean the corona wire.
- The drum unit or the toner and drum assembly is not seated correctly, so remove the assembly, reseat the toner cartridge in the drum, and reinstall it.
If the message persists after either fix, Brother says to replace the drum unit.
On some models the page also reads “Slide the Green tab on Drum Unit”, which is the corona wire cleaning step.
No Drum Unit and Cannot Detect
No Drum Unit means the drum is not installed correctly, and Brother says to reinstall the toner and drum assembly.
Cannot Detect means the machine cannot see the toner cartridge or drum unit.
For that one, Brother says to remove the assembly, take the toner cartridge out of the drum, put it back in, and reinstall the assembly.
How to reseat the toner and drum assembly
Brother’s repeated fix across these messages is a reseat.
- Open the front cover.
- Remove the toner cartridge and drum unit assembly.
- Take the toner cartridge out of the drum unit.
- Put the toner cartridge back into the drum unit.
- Reinstall the assembly in the machine.
Brother’s pages describe this sequence in words only, so follow the pictures in your model’s own guide.
Related toner messages
Drum problems are often mixed up with toner messages that appear at the same time.
| Message | Brother’s action |
|---|---|
| Toner Low | You can still print; order a new cartridge |
| Replace Toner / Toner Ended | Replace the toner cartridge |
| No Toner | Reseat the toner in the drum, and replace it if the problem continues |
| Cartridge Error | Reseat the toner in the drum and reinstall the assembly |
| Wrong Toner | Install a cartridge with the correct supply order number |
Other messages that stop a print job
Some messages that appear alongside drum trouble are not about the drum at all.
| Message | Brother’s action |
|---|---|
| Cooling Down | Let the machine cool, keep the vents clear, and printing resumes on its own |
| Self-Diagnostic | Hold the power button to switch off, wait a few seconds, switch on, and leave it idle for 15 minutes |
| Cannot Print ## | Switch off, wait a few minutes, switch back on, then contact Brother if it persists |
| Out of Memory | Lower the print resolution |
If the fan is not spinning during Cooling Down, Brother says to unplug the machine for several minutes and plug it back in.
If the drum message comes with a jam
A jam inside the machine can disturb the assembly, and Brother’s Jam Inside step is to remove the drum and toner before clearing the paper.
After clearing it, seat the assembly again and close the cover fully.
Our guide to a Brother printer that will not print covers other causes of a printer that stops.
When to contact Brother
Brother says most errors and routine maintenance can be handled by the user.
If a message persists, contact Brother Customer Service or your local Brother dealer.
In the USA, Brother lists 1-877-BROTHER (1-877-276-8437) and FAQs at support.brother.com/faqs.
Sources
Brother online user’s guides: Error and Maintenance Messages (HL-L2460DW), Reset the Drum Counter (HL-L2460DW) and Error and Maintenance Messages (DCP-L2640DW and related models).