How To Fix Canon PIXMA Cannot Communicate With Scanner (2026)

When a Canon PIXMA will print but will not scan, Windows usually shows a message that says IJ Scan Utility or ScanGear cannot communicate with the scanner.

Canon’s manuals tie that message to a numbered code, and each code has its own short fix.

This guide follows those pages, starting with the checks Canon lists first.

Quick answer: what to try first

CheckWhat Canon says
Power and errorsMake sure the printer is on and not showing a support code
USBTry another USB port, and skip any USB hub
NetworkCheck the connection and reconnect, then pick the scanner in IJ Network Scanner Selector EX2
RestartRestart the computer
Still failingRemove the MP Drivers and reinstall them from Canon’s website

Step 1: run Canon’s basic checks

Canon’s “Scanner Does Not Work” page lists seven checks in this order.

  1. Make sure the scanner or printer is turned on.
  2. Look for a printer error on the screen, because an error can block scanning.
  3. Connect the USB cable to a different USB port on the computer.
  4. If the cable goes through a USB hub, plug it straight into the computer instead.
  5. On a network connection, check the connection status and reconnect.
  6. Restart the computer.
  7. Reinstall the MP Drivers from the setup disc or Canon’s website.

If the printer is showing a support code, clear that first, and our Canon error 5100 and 5B00 guide or Canon ink absorber guide may match it.

Step 2: match the ScanGear error code

If a number appears in the message, Canon’s ScanGear error list gives a different action for each one.

CodeCanon’s meaningAction
140Printer is in use, or it has an errorWait for printing to end, or clear the support code on the printer
145Cannot communicate with the scannerCheck power, the cable or network, the selected source, then reinstall drivers
155, 156, 157Cannot communicate with the scannerCheck the cable, power and network connection
201A required file is missing or damagedDelete the MP Drivers and reinstall them
202Internal errorRestart the scanner and computer, reinstall drivers, and check that WIA is running
206Scanner in use by another program or userClose the ScanGear that is open
207No scanner selectedClick Scanner Selection and choose one
250An error occurredTurn the device off and on

Canon lists codes 1, 4, 10, 122, 151, 175, 176 and 177 as “Error in scanner,” and says to check the connection, reinstall the MP Drivers and, if it repeats, contact the service center.

Step 3: check the WIA service for code 202

For code 202, Canon tells Windows users to confirm that Windows Image Acquisition (WIA) is running.

  1. Open Control Panel, then System and Security, then Administrative Tools.
  2. Double-click Services.
  3. Find Windows Image Acquisition (WIA) and check that it is running or started.

Canon also says to delete unnecessary drivers that may interfere, and to scan with another program if your app does not fully support TWAIN.

Step 4: select the scanner on a network connection

If your PIXMA is connected by Wi-Fi or Ethernet, Windows must be told which scanner to use.

  1. Check that IJ Network Scanner Selector EX2 is running. Its icon sits in the notification area, behind the hidden-icons arrow.
  2. If it is not running, open Start, then Canon Utilities, then IJ Network Scanner Selector EX2.
  3. Right-click its icon, choose Settings, pick your printer under Scanners, and click OK.
  4. Open IJ Scan Utility and set Scanner to “Canon XXX series Network,” where XXX is your model.

Canon says the MAC address is usually selected for you after network setup, and that a device missing from the list means the MP Drivers are not installed or network setup was not finished after installing them.

Canon also warns that network scanning is slower than USB and that several users cannot scan at the same time.

If the printer itself keeps dropping off Wi-Fi, see our Canon Wi-Fi reconnect guide first.

Step 5: remove and reinstall the drivers

Canon’s answer for codes 201, 208 and several others is the same, so do it once and do it fully.

  1. Unplug the USB cable.
  2. Remove the MP Drivers using Canon’s “Deleting the Unnecessary MP Drivers” page.
  3. Open Control Panel, then Programs and Features, select Canon IJ Scan Utility and choose Uninstall/Change.
  4. Reinstall the MP Drivers and IJ Scan Utility from Canon’s website.

Canon gives these steps for a scanner that stopped working after a Windows upgrade, and logging in as an administrator helps if Windows asks for rights.

Other messages in the Canon list

CodeProblemCanon’s action
152Not enough memoryClose other programs
203Not enough free disk spaceDelete files, then scan again
208IJ Network Scanner Selector cannot be foundDelete and reinstall the MP Drivers
252Cannot write or read the fileClose programs, free disk space, scan again

If you use a Mac

Canon’s IJ Scan Utility for Mac has its own list, and its code 157 also says to check that the scanner is on, reconnect on a network, and restart the computer if the error stays.

For code 201 or 230 on a Mac, Canon says to reinstall the scanner driver and IJ Scan Utility from its website.

These Mac codes also come up when a scan starts but cannot be saved.

Mac codeProblemCanon’s action
231Disk space is insufficientDelete unneeded files, then scan again
232The disk is write-protectedRemove the write protection or use another disk
242, 243Cannot write or read the fileCheck folder access permissions for the temporary files folder and the Save in folder
244No privileges for the folderGrant access permission to that folder
248Scanner is not selectedClick Scanner Selection and choose the scanner

Canon says code 245 means text could not be detected, so match Document Language in General Settings to your document.

Code 153 means the image cannot be opened in the chosen application, and Canon says to lower the resolution or output size and scan again.

Official Canon sources

Leave a Reply

Your email address will not be published. Required fields are marked *