How To Open BIOS Or UEFI Settings In Windows 11 (2026)
The BIOS or UEFI screen is where you change boot order, Secure Boot, TPM and other low-level PC settings.
Windows 11 calls it UEFI Firmware Settings, and Dell uses BIOS, UEFI, system firmware and System Setup for the same screen.
The steps below follow Dell’s and ASUS’s support pages, Microsoft’s Surface UEFI guide and Microsoft’s shutdown command reference.
Quick answer
| Situation | Best method |
|---|---|
| Windows starts normally | Settings > System > Recovery > Advanced startup > Restart now |
| You are at the sign-in screen | Hold Shift, select Power > Restart |
| You like typing commands | shutdown /r /fw /t 0 in Terminal as administrator |
| Windows will not start | Tap the maker’s key (Dell: F2) as the logo appears |
| Surface | Hold Volume up, then press the power button |
Before you open the firmware settings
Every method restarts the PC, so save your work and close your apps first.
Dell says to suspend BitLocker first if you plan to change Secure Boot, TPM or the boot mode.
On Dell’s page that means Settings > Privacy & security > Device encryption (or BitLocker drive encryption) > Suspend protection, then turning it back on afterward.
If you skip this and the PC asks for a key, see our guide to finding your BitLocker recovery key.
Open it from Windows 11 Settings
- Select Start > Settings, or press the Windows key + I.
- Select System, then Recovery.
- Next to Advanced startup, select Restart now, then select Restart now again to confirm.
- On the Choose an option screen, select Troubleshoot > Advanced options.
- Select UEFI Firmware Settings, then select Restart.
Microsoft’s Surface page lists the same route, and the PC restarts straight into the firmware screen.
Open it with Shift and Restart
- At the sign-in screen, select the Power icon.
- Hold Shift and select Restart.
- Keep holding Shift until Choose an option appears.
- Select Troubleshoot > Advanced options > UEFI Firmware Settings > Restart.
Dell says the same Shift and Restart trick works from the Start menu on the desktop.
Open it with a command
- Select Start, type Terminal, and select Run as administrator.
- Type shutdown /r /fw /t 0 and press Enter.
Microsoft says the /fw switch, combined with a shutdown option, makes the next restart go to the firmware user interface.
The /r switch restarts the PC and /t 0 sets a timeout of zero seconds, so it restarts at once.
Dell adds that this needs administrator rights, and that shutdown /r /o /t 0 opens the recovery menu instead.
Open it at startup with a key
This is the method that works even when Windows will not start.
- Shut the PC down completely, then press the power button.
- As the Dell logo appears, tap F2 about once per second.
- Keep tapping until the BIOS setup opens, and note Dell says you may see Preparing to enter Setup.
Dell says to tap rather than hold, and that a Windows logo with spinning dots means you started too late.
If F2 changes your screen brightness, Dell says to use Fn + F2.
Dell also offers F12 at the same moment, which opens the One Time Boot Menu where you can choose BIOS Setup or System Setup.
Startup keys by maker
| Maker | What the official page says |
|---|---|
| Dell | Tap F2 at the logo for setup, or F12 for the One Time Boot Menu |
| Dell tablet | Hold Volume up, press and release Power, keep holding until the boot menu appears |
| ASUS notebook | Hold F2, press the power button, release F2 when the BIOS screen appears |
| Older ASUS desktop | Hold Del during startup |
| ASUS handheld | Hold Volume Down, then press the power button |
| Surface | Hold Volume up, press and release Power, release when the UEFI screen appears |
For other makers such as HP and Lenovo, check the manual or support page for your exact model, because the key differs between models.
Open UEFI on a Surface
- Shut down your Surface and wait about 10 seconds.
- Press and hold the volume-up button, then press and release the power button.
- Keep holding volume-up after the Microsoft or Surface logo appears.
- Release it when the UEFI screen appears.
Microsoft says Surface UEFI can only be changed during startup, and it covers Surface Pro 4 and later, Surface Laptop models, Surface Go, Surface Book and Surface Studio.
Its menus include PC information, Security, Boot configuration, Date and time, About and Exit, and you choose Restart now under Exit to save and restart.
If UEFI Firmware Settings is missing
Dell lists these causes when the option is not under Advanced options.
| Possible cause | What Dell says |
|---|---|
| Legacy boot mode | Check BIOS Mode in msinfo32 |
| MBR drive | The drive may use MBR instead of GPT |
| Recovery Environment | Windows RE may be disabled or damaged |
Use F2 or F12 at startup instead, and see our guides to checking your BIOS version and UEFI mode and converting MBR to GPT.
If the key press is missed
Dell says Fast Startup can shorten the window for pressing F2.
It affects only Shut down, not Restart, so selecting Restart and tapping F2 is the quickest workaround.
You can also turn off Fast Startup if you want a longer window.
If the keyboard does nothing
Dell says wireless or Bluetooth keyboards may not respond before Windows loads.
Plug a wired USB keyboard directly into the computer and try again.
If the firmware asks for a password
Dell says a BIOS administrator password on a work computer must be handled by your IT administrator, and that Dell cannot remove or recover it.
Microsoft says you cannot reset a Surface UEFI password and Microsoft cannot retrieve it.
What people change here next
- Our guide to turning on Secure Boot.
- Our guide to checking and turning on TPM 2.0.
- Our guide to turning on virtualization.