|

How To Turn On Secure Boot In Windows 11 (2026)

Secure Boot is a Windows security feature that helps stop malicious software from loading while your PC starts.

It is switched on or off in your PC’s UEFI firmware, not inside Windows, so you have to restart into the firmware settings to change it.

The steps below follow Microsoft’s Secure Boot page, Dell’s and ASUS’s support pages, and Microsoft’s Surface UEFI guide.

Quick answer

What you wantWhere to do it
See if Secure Boot is onmsinfo32 > System Summary > Secure Boot State
Open the firmware settingsSettings > System > Recovery > Advanced startup > Restart now
Required boot modeUEFI, not Legacy BIOS or CSM
Setting to changeSecure Boot set to Enabled, then Save and Exit

Check whether Secure Boot is already on

  1. Press the Windows key.
  2. Type msinfo32 and press Enter.
  3. In System Summary, read BIOS Mode and Secure Boot State.

Dell’s support page uses this check and explains the three results in the table below.

BIOS ModeSecure Boot StateWhat it means
UEFIOnSecure Boot is enabled, so nothing to do
UEFIOffSecure Boot is disabled in the firmware; turn it on
LegacyUnsupportedLegacy mode does not support Secure Boot; switch to UEFI first

Our Secure Boot certificate update guide covers the separate Windows Security certificate message, which is a different question from turning the feature on.

Before you change anything

Dell warns that switching a PC from Legacy to UEFI makes the current Windows installation unbootable, so back up your data first.

ASUS says that if BitLocker or Device Encryption is active, changing BIOS settings may ask for your BitLocker recovery key.

Microsoft says a Windows 10 PC only needs to be Secure Boot capable, meaning UEFI is enabled, to upgrade to Windows 11, although turning Secure Boot on is still recommended.

Open the UEFI firmware settings from Windows

  1. Save your work, then open Settings and select System > Recovery.
  2. Next to Advanced startup, select Restart now.
  3. Select Troubleshoot > Advanced options > UEFI Firmware Settings.
  4. Select Restart.

Microsoft’s page names this route, and our TPM 2.0 guide uses the same firmware screen for the TPM setting.

Switch the boot mode from Legacy to UEFI

Microsoft says to switch from Legacy BIOS, also called CSM mode, to UEFI, and to make UEFI the first or only option if your PC offers both.

Dell gives these steps for a Dell PC that shows Legacy in msinfo32.

  1. Restart and press F2 when the Dell logo appears.
  2. Open Boot or Boot Sequence and find Boot List.
  3. Change Boot List from Legacy to UEFI.
  4. Select Apply or Save and Exit.
  5. Reinstall Windows in UEFI mode and restore your data.

Turn on Secure Boot on a Dell PC

  1. Restart and press F2 at the Dell logo.
  2. Find the Secure Boot option, which Dell says is typically in the Boot Configuration area but varies by model.
  3. Set Secure Boot to Enabled.
  4. Select Apply or Save and Exit.

The PC then restarts to the Windows desktop.

Turn on Secure Boot on an ASUS PC

ASUS says to shut the device down fully, hold F2, then press the power button, and release F2 when the BIOS screen appears.

ASUS devicePathSetting
Notebook, all-in-one or handheldF7 / Advanced Mode > Security > Secure BootSecure Boot Control: Enabled
DesktopF7 / Advanced Mode > Boot > Secure BootOS Type: Windows UEFI mode

On either type, press F10 and confirm to save and exit.

ASUS says the status shows Active or Not Active only after you save and exit.

ASUS gaming handhelds start the BIOS with Volume Down plus the power button, and some older ASUS desktops use Del.

If ASUS shows Not Active

  1. On a notebook, set Secure Boot Control to Enabled and select Key Management.
  2. Select Reset To Setup Mode and choose Yes.
  3. Select Restore Factory Keys and choose Yes.
  4. Press F10 and confirm.

On an ASUS desktop the matching options are Clear Secure Boot Keys and Install Default Secure Boot Keys under Key Management, with Secure Boot Mode set to Custom.

Surface devices

  1. Shut the Surface down and wait about 10 seconds.
  2. Hold Volume-Up, then press and release Power.
  3. Keep holding Volume-Up until the UEFI screen appears.

Microsoft’s Surface guide lists the Security page options as Disable Secure Boot and Configure Secure Boot with custom third-party certificates, and warns that disabling it shows a warning at startup.

Check that it worked

Open msinfo32 again and confirm BIOS Mode says UEFI and Secure Boot State says On.

Problem (Dell’s page)Likely cause and fix
Secure Boot option is greyed out or missingBoot mode is probably Legacy; switch to UEFI and reopen the firmware settings
Windows will not start after switching to UEFIWindows was installed in Legacy mode and must be reinstalled in UEFI mode
msinfo32 still says Off after savingThe change was not saved; re-enter the firmware, confirm Enabled, and apply again

Official sources

Microsoft’s Secure Boot page also links to the Gigabyte, HP, HPE and Lenovo guides for those brands.

Leave a Reply

Your email address will not be published. Required fields are marked *