How To Fix Chromecast Or Google TV Streamer No Signal (2026)
A black screen or No Signal message from a Chromecast with Google TV or Google TV Streamer is nearly always a power, HDMI or input problem.
Google ties the fix to what the status LED on the device is doing, so the LED tells you which steps to follow.
This guide follows Google’s no signal or black screen article and its video quality page.
Quick answer: match the LED to the fix
| What you see | Where to go |
|---|---|
| Black screen, white LED (solid or blinking) | Full TV and device power cycle |
| Black screen, solid red or orange LED | Check the included power cord, then power cycle, then reset |
| Blinking red or orange LED, or No Signal | TV power cycle, then try another TV |
| Black screen, no LED | Test the USB port, outlet and power cable |
| Google TV text, spinning logo, then black | TV power cycle without plugging in first |
Start with power and input
- Connect the device directly to a power source with the cord and adapter from the box.
- Set the TV to the HDMI input the device is plugged into, such as HDMI 1 or HDMI 2.
- If the screen is still black, unplug the device’s power cord, wait one minute, and plug it back in.
- If it is still black, disconnect all other HDMI devices and unplug the TV’s power cord for 30 minutes.
Google stresses unplugging the power cord, not the HDMI cable.
HDMI error steps
- Confirm the HDMI cable sits firmly in the TV port.
- Try a different HDMI input.
- Use a compatible HDMI extension cable if you use one.
- If the error happens in one app, update that app.
- Update the streaming device to the latest firmware.
- Update the TV to the latest firmware.
Which HDMI extension cable to use
| Device | Extension must support |
|---|---|
| Chromecast with Google TV (4K) | 4K and HDMI 2.0 |
| Google TV Streamer (4K) | 4K and HDMI 2.1 |
Google’s setup page also lists an Ultra High Speed HDMI 2.1 certified cable for the Google TV Streamer.
HDCP errors
- Unplug the device from the TV, receiver or soundbar.
- Reboot the device and the TV, receiver or soundbar.
- Reconnect the device and seat the HDMI cable firmly.
- Check whether content plays.
If it persists, try another HDMI input, plug the device straight into the TV instead of a switch, receiver or soundbar, and update both firmware versions.
Our guide to the HDCP H1001 error covers the same message on another service.
Samsung TV flicker or brief blackouts
If a Samsung TV loses signal for a few seconds at a time, Google says to turn off the HDMI UHD Color setting on the TV.
Black screen with a white LED
- Switch the TV off and unplug its power cord.
- Disconnect the streamer from its HDMI port and unplug its power.
- Turn the TV on, then reconnect power to the streamer without plugging it into the TV.
- Wait 30 seconds.
- Plug the streamer into an HDMI port and select that input.
If the TV has several HDMI ports, repeat the process on a different one, and then test the device on another HDMI TV.
Red or orange LED
| LED | Next step |
|---|---|
| Solid red or orange | Use the included cord and adapter, then run the white LED procedure, then factory reset only as a last step |
| Blinking red or orange, or No Signal | Run the white LED procedure, then test on another HDMI TV |
No LED at all
- Check the USB port you use by charging a phone from it.
- Try a different power source, such as a wall outlet.
- Try a different power cable and adapter from the one in the box.
Our Hisense HDMI no signal guide and Sony HDMI no signal guide cover the TV side of the same message.
Spinning logo then a black screen
If the screen shows Google TV text and a spinning logo before going black, run the white LED procedure and do not plug the device into the TV until the fifth step.
If it stays black, test the device on another HDMI TV.
Flicker, stutter or poor picture
Google’s video quality page lists settings to try when video freezes or stutters.
- Turn off every HDR format: open Settings, Display and sound, Advanced display settings, then Format selection, choose Manual and switch the HDR options off.
- Lower the resolution from 4K to 1080p under Settings, Display and sound, Resolution.
- Change the motion compensation setting in the TV picture menu.
Check your TV and audio equipment limits
The video quality page says the supported resolution depends on the model, so a mismatch anywhere in the HDMI chain can cause trouble.
| Device | What the TV and audio gear must support | HDMI cable rating |
|---|---|---|
| Chromecast with Google TV (4K) | Up to 4K | HDMI 2.0 or later, supporting 4K |
| Chromecast with Google TV (HD) | Up to 1080p | Not stated |
| Google TV Streamer (4K) | HDMI 2.1 | HDMI 2.1, supporting 4K |
If the Streamer plugs directly into the TV, Google says to connect your soundbar or receiver to the TV’s eARC HDMI port with an HDMI 2.1 cable.
If you can see the home screen, update and restart from the menu
When the picture works but is unstable, a firmware update and restart are the first things Google lists.
| Device | Restart path |
|---|---|
| Chromecast with Google TV | Settings in the upper right, then System, then Restart |
| Google TV Streamer | All settings in the upper right, then System, then Restart |
Google points to its Chromecast release notes page to compare your firmware version against the latest.
Factory reset as the last resort
A reset erases all data and cannot be undone, so you will need to set up the device and Wi-Fi again.
| Method | Steps |
|---|---|
| Voice Remote | Select your profile, All settings, System, About, Factory Reset |
| Device button | With the device powered on, hold the back button for 10 to 12 seconds, then release when the LED goes from blinking yellow to solid white |
Google adds that Ambient Screensaver settings need to be reconfigured afterward if you use them.
For a Google TV Streamer that seems unresponsive, check its power connection before resetting, and if you plan to hand it to someone else, remove it from the Google Home app first.
When to contact support
If nothing works, Google asks you to complete a short feedback survey for its engineers, linked from the article.
You can also use the contact us link on the Google Nest help page if you still cannot set the device up.