|

How To Fix Sony TV HDMI No Signal Message (2026)

A Sony TV that shows No Signal or a blank screen from an HDMI device is usually dealing with the wrong input, a sleeping device or a bad cable.

Sony has a dedicated support article for the No Signal message, and it covers cable boxes, satellite receivers and HDMI players separately.

The steps below follow that article, plus Sony’s separate guidance on the HDMI signal format for 4K and HDR.

Quick answer: fixes in order

StepWhat to doWhy
1Press Input and pick the one that matches the portThe TV may be on a different input
2Turn the source device off and onIt may be in standby
3Turn the TV off and onClears a temporary glitch
4Reseat the HDMI cable at both endsA loose cable gives no signal
5Try another HDMI port, then change the input to matchRules out a faulty port
6Power reset the source device and the TVClears stuck states in either one

What causes the No Signal message

Sony’s article does not list causes outright, but its steps point to a short set of them.

  • The wrong TV input is selected.
  • The source device is off or in standby.
  • A temporary glitch in the TV or the source device.
  • A loose, damaged or faulty cable.
  • A faulty HDMI port.
  • A provider outage, a splitter on the line or a defective cable box or receiver.

Select the correct input

Press the Input button on the remote and cycle through the inputs until the one that matches the port in use is selected.

Look at the back or side of the TV to see which HDMI number the cable is plugged into.

Then confirm the connected device is on and not in standby, and turn it off and on again.

Fix an HDMI player or streaming box

For a Blu-ray player, game console or similar HDMI device, Sony lists these steps.

  1. Make sure the device is on and not in standby, then turn it off and back on.
  2. Check that the TV input matches the HDMI port the device uses.
  3. Unplug the device, wait one minute, plug it directly into a wall outlet and turn it on.
  4. Reseat both ends of the HDMI cable, and try a different or new cable if the problem continues.
  5. Move the device to a different HDMI port on the TV and change the input to match.

Sony specifically says to plug the device into the wall, not a power strip, during the power reset.

Fix a cable box

Cable boxes have extra steps because the signal also depends on your provider.

  1. Turn the cable box off and on, then power reset it by unplugging for one minute.
  2. Check with your provider for a local outage.
  3. Check the cable between the TV and the box, and replace it if nothing improves.
  4. Try a different TV port and select the matching input.
  5. Remove any splitters or extra devices from the incoming cable unless your provider requires them.
  6. Connect another source to the same TV input to see whether the box is the problem.

If another device works on that input but the cable box does not, Sony says the box may be defective and you should contact your provider.

Fix a satellite receiver

A satellite receiver follows a similar path, with one extra check outside the house.

Look for weather or obstructions such as tree limbs or birds blocking the dish.

After that, power reset the receiver, check for a provider outage, replace the cable if needed and try another HDMI port.

Fix a direct antenna connection

For an antenna, Sony says to try changing the channel first.

If the problem remains, adjust the antenna direction for better reception.

If only the current channel is affected, rescan the channels using the TV’s auto program feature.

Which fix applies to which source

Sony splits the No Signal steps by what is connected, so start with the row that matches your setup.

SourceExtra step Sony listsSection above
HDMI player or consoleMove to a different HDMI port and change the inputFix an HDMI player
Cable boxRemove splitters and test another source on the same inputFix a cable box
Satellite receiverCheck the dish for weather or obstructionsFix a satellite receiver
AntennaAdjust the antenna and rescan channelsFix a direct antenna connection

A different working device on the same input is the quickest way to tell whether the TV or the original source is at fault.

Power reset the TV

Sony’s restart guide for Google TV and Android TV gives a remote method and an unplug method.

  1. Unplug any USB hard drive from the TV.
  2. Point the remote at the TV and hold POWER for about 5 seconds until Power off appears, then wait about one minute.
  3. If that does not help, turn off the TV, unplug the power cord, press the TV power button once, and leave it unplugged for 2 minutes.
  4. Plug the cord back in and select the right input.

If the picture only fails with 4K or HDR

A 4K or HDR device can show no signal when the cable or the TV setting cannot carry the signal.

SignalCable Sony recommends
4K 50p or 60pHigh-Speed HDMI cable
4K Enhanced Format at 18GbpsPremium High-Speed HDMI cable
4K Enhanced Format above 18GbpsUltra High-Speed HDMI cable

Sony says some ports may not support 4K 60p with HDR, so check which port supports your signal.

Turn on the HDMI signal format setting

Sony says higher-quality 4K input may need the HDMI signal format set to Enhanced.

  1. Open Settings from Quick Settings, or press HOME and choose Settings.
  2. Choose Channels & Inputs or Watching TV if either appears.
  3. Choose External inputs.
  4. Open HDMI signal format and choose the Enhanced option your TV offers.

The options vary by TV model and signal, and Sony lists names such as Enhanced format (Dolby Vision), Enhanced Format (VRR) and Enhanced format (4K120).

If the screen is lit but unstable, read Sony TV screen is flickering.

If you hear audio with no picture, see Sony TV with sound but no picture.

If the TV never gets past the logo, Sony TV stuck on logo screen is the better match.

When to contact Sony support

Sony’s article says the TV may need service if basic troubleshooting does not clear the No Signal problem.

Before you call, note which input, which device and which cable you tested, since a second working device on the same port points to the original device.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *