|

How To Fix Hisense TV HDMI No Signal (2026)

A Hisense TV that shows “No Signal” is usually fine, and the problem sits in the input, the cable or the connected device.

Most fixes take under a minute each, so work through them in the order below.

This guide uses Hisense, Roku and Google TV support material, and each step is labeled by where it applies.

Quick answer: what to try first

What you seeTry this first
No Signal on one HDMI inputPress Input or Source on the TV remote and pick the port the device is plugged into
Roku or other device lit up but no pictureReseat the HDMI cable and try a different HDMI port
Picture drops now and then from a cable boxUnplug the box for 60 seconds, then try Menu > HDMI Format
TV jumps to the wrong inputTurn off HDMI control (CEC) or 1-touch play
Picture works but no soundCheck the audio output setting for ARC or eARC

Select the correct input

Roku calls a wrong input the most common cause of a missing picture.

Use the TV remote, not the streaming remote, and press Input or Source.

Pick the HDMI number printed beside the port where your device is connected.

If the TV cycles through inputs on its own, pause about 10 seconds on each so it can detect the signal.

Reseat the cable and try another port

A loose or damaged cable is the next most likely cause.

  1. Unplug the HDMI cable from the TV and from the device.
  2. Wait about 10 seconds.
  3. Plug both ends back in firmly, using the same port on the TV.
  4. If there is still no picture, move the cable to a different HDMI port and select that input.
  5. Try a different HDMI cable to rule out a bad one.

If you use a Roku Streaming Stick, make sure it is pushed fully into the HDMI port.

Power cycle the TV and the device

Roku suggests unplugging both devices and removing any power strips or extension cords.

After 10 seconds, plug both directly into wall outlets and turn them on.

A Hisense manual for a Google TV model also says to unplug the TV for 60 seconds if the picture is black and white or missing.

A delay of a few seconds before the picture appears is normal while the TV starts up, according to the same manual.

Bypass the receiver or soundbar

Receivers and soundbars add another link that can fail.

Roku advises connecting the player straight to the TV when an AV receiver is in the chain.

Note the new HDMI port number, switch the TV to that input and test again.

If the picture returns, the receiver, its HDMI cable or its settings are the cause.

Change the HDMI format for a cable box

The Hisense manual covers a cable box that loses signal now and then.

First unplug the cable and plug it back in after 60 seconds.

If the problem continues, open Menu and try HDMI Format while HDMI is the active input, and try another port or cable.

Some devices, such as DVD players, must also be set to output over HDMI in their own settings.

Turn off HDMI control (CEC)

CEC lets devices wake the TV and switch inputs, and it can pull the TV away from the input you want.

Roku says to turn off 1-touch play, and if that is not enabled, to turn off CEC on the TV.

PlatformWhere to find it
Hisense Google TV model (75U7G manual)Settings > Inputs > HDMI control, plus Device auto power off and TV auto power on
Hisense Roku TV (Roku support)Home > Settings > System > Control other devices > uncheck 1-touch play, then power cycle
Other Hisense modelsLook for HDMI control or CEC in the TV settings, since Roku gives no path for the TV itself

Menu names vary by model and software version, so use the table as a guide.

Update the TV software

Roku lists a firmware update among its fixes for a TV that switches to the wrong device.

Connect the TV to the internet and let it install any update.

On the Google TV model in the manual, the path is Settings > Device Preferences > About > System update.

Fix HDMI picture with no sound

If the picture works but a soundbar stays silent, the audio settings are the next place to look.

SettingPath in the Hisense 75U7G manual
Audio outputSettings > Sound > Audio Output > eARC/ARC
eARC switchSettings > Sound > eARC set to On, if the device supports eARC
Digital audio formatSettings > Sound > Advanced Settings > Digital Audio Out, try PCM, Dolby Digital or Dolby Digital Plus
PortConnect the sound system to the TV HDMI port labeled eARC/ARC

The manual adds that eARC and ARC work only with an audio receiver that supports them.

Test the device on another TV

Roku suggests connecting the player to a different TV to learn whether the TV or the player is at fault.

If the same device works elsewhere, focus on the Hisense TV, its HDMI port and its settings.

If it fails on both TVs, focus on the device, its cable and its power supply.

Check power for streaming sticks and players

Roku says some players do not get enough power even when the light is on.

Use the power adapter that came with the device when possible.

If a flashing red light or a low-power warning appears, plug the player directly into a wall outlet with the supplied cable.

Picture is wavy, striped or distorted

A picture that is on screen but looks wrong is a different problem from a missing signal.

The Hisense manual lists nearby electrical appliances as a cause of a wavy picture, so move them away from the TV.

It also suggests another power outlet, and it says a phone within about 1 meter of the TV can add noise.

When to contact Hisense

If every input shows no signal even with a known good device and cable, the TV itself may need service.

The Hisense manual says the on-TV Help menu shows the support URL and number under Advanced System > Help > Support Information.

Products can also be registered at Hisense USA support.

If the screen stays dark after the TV powers up, see Hisense TV turns on but no picture.

For a black screen with sound, read Hisense TV black screen.

Audio complaints are covered in Hisense TV poor audio quality.

Another brand with the same symptom is covered in Sony TV HDMI no signal.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *