|

How To Suspend BitLocker In Windows 11 (2026)

Suspending BitLocker pauses its startup checks so you can change firmware or boot settings without being asked for your recovery key.

You can do it from Control Panel in a few clicks or with one PowerShell command, and Microsoft documents both.

Protection must be switched back on afterwards, and the steps below show how to do that and how to confirm it worked.

Quick answer

What you wantHow
Suspend in Control PanelControl Panel > System and Security > BitLocker Drive Encryption > Suspend protection > Yes
Suspend in PowerShell (admin)Suspend-BitLocker -MountPoint “C:” -RebootCount 0
Resume in Control PanelControl Panel > System and Security > BitLocker Drive Encryption > Resume protection > Yes
Resume in PowerShell (admin)Resume-BitLocker -MountPoint “C:”

When to suspend BitLocker

Microsoft says to suspend protection on a system drive before installing updates that change boot components or firmware.

Its page for non-Microsoft updates lists three examples, shown below.

  • Computer manufacturer firmware updates
  • TPM firmware updates
  • Non-Microsoft application updates that modify boot components

Microsoft’s PowerShell reference gives the same idea in one line: you might suspend protection for firmware upgrades or system updates.

Microsoft’s recovery overview also recommends suspending for planned changes, such as known hardware or firmware upgrades.

If protection is not suspended, Microsoft warns that Windows will not recognize the BitLocker key and asks for the recovery key at the next restart, and that can repeat on every restart.

What suspending does and does not do

QuestionAnswer from Microsoft
Is the drive decrypted?No. The drive stays fully encrypted, and new data written to it is still encrypted.
Is it still protected?No. The encryption key is made available in the clear, and BitLocker does not validate system integrity at startup.
Do I need the recovery key to resume?No. Suspend and resume reseals the key without it.
Does it turn back on by itself?Yes, after the next restart, unless you set a different reboot count.

Because the drive is unprotected while suspended, keep the suspended time as short as you can.

Before you suspend

Make sure you can find your recovery key, in case something goes wrong during the update.

Our guide to finding your BitLocker recovery key shows where Microsoft stores it.

If you only want to know which firmware you have first, see how to check your BIOS version.

Suspend BitLocker in Control Panel

  1. Open Control Panel.
  2. Select System and Security.
  3. Select BitLocker Drive Encryption.
  4. Select Suspend protection next to the drive you are about to change.
  5. Select Yes to confirm.

Dell’s own BIOS-update article for BitLocker systems uses the same Control Panel route and says to install the BIOS after suspending.

Suspend BitLocker in PowerShell

  1. Select Start, search for PowerShell, right-click Windows PowerShell and choose Run as administrator.
  2. Type the command below and press Enter.

Suspend-BitLocker -MountPoint "C:" -RebootCount 0

Replace C: with another drive letter if you are suspending a different drive.

A RebootCount of 0 keeps protection suspended until you resume it yourself, which suits firmware updates that restart the PC more than once.

Microsoft’s Surface guidance notes that TPM and UEFI updates may need multiple reboots, and it uses this same command before the update.

Choose a reboot count

SettingResult
No -RebootCountDefaults to 1, so protection returns after one restart
-RebootCount 3Protection returns after three restarts
-RebootCount 0Stays suspended until you run Resume-BitLocker or choose Resume protection
Allowed range0 to 15

The older manage-bde tool does the same job, and its documented form is manage-bde -protectors -disable C: -rc 3 to suspend until three restarts have passed.

Microsoft’s manage-bde page adds that this removes no key protectors.

Install the update, then resume

  1. Install the BIOS, UEFI or TPM firmware update from your PC maker.
  2. Let the PC restart as many times as the update needs.
  3. Once the update has finished, resume protection using the table at the top.

If you are not sure how to reach your firmware settings, follow our guide to opening BIOS or UEFI in Windows 11.

The same care applies when you turn on the TPM or turn on Secure Boot, since both change what BitLocker checks.

Resume BitLocker protection

In Control Panel, go to System and Security > BitLocker Drive Encryption and select Resume protection, then Yes.

In an administrator PowerShell window, run Resume-BitLocker -MountPoint "C:".

Microsoft says that running Resume-BitLocker on a volume that is not suspended has no effect, so it is safe to run twice.

Check that protection is back on

In an administrator PowerShell window, run Get-BitLockerVolume -MountPoint C | Format-List.

Look at the ProtectionStatus line, where On means protected and Off means protection is still suspended.

Microsoft’s example output for a protected C: drive shows VolumeStatus FullyEncrypted and ProtectionStatus On.

If Windows still asks for the recovery key

Microsoft’s recovery overview lists causes such as updating BIOS or UEFI firmware, clearing or turning off the TPM, and changing the boot manager.

Enter the recovery key from your Microsoft account, as covered in our recovery key guide.

If you would rather stop using encryption altogether, see how to turn off BitLocker device encryption.

For work or school PCs, ask your administrator before suspending, because the keys and policies may be managed for you.

Official sources

Leave a Reply

Your email address will not be published. Required fields are marked *