|

DRIVER_POWER_STATE_FAILURE Blue Screen Fix In Windows 11 (2026)

DRIVER_POWER_STATE_FAILURE is a Windows blue screen with the stop code 0x9F.

It means a driver was left in an invalid power state, which often shows up when the PC sleeps, wakes or shuts a device down.

This guide follows Microsoft’s bug check page and its support article on stop codes.

Quick answer

StepWhat to do
1Remove or update any driver or hardware you added just before the blue screen began
2Open Device Manager and update any device marked with a yellow exclamation point
3Check the System log in Event Viewer for critical errors near the crash time
4Turn off power saving in Power Options to see if the crashes stop
5Run the maker’s hardware diagnostics and look for a BIOS or firmware update
6Install Windows updates, and use a restore point if nothing else works

What DRIVER_POWER_STATE_FAILURE means

Microsoft gives the value as 0x0000009F and says it means a driver is in an inconsistent or invalid power state.

Windows moves devices between power states as the PC sleeps, wakes or saves power.

When a driver does not finish one of those changes correctly, Windows stops with this error.

Microsoft says its bug check article is written for programmers and points customers to its Troubleshoot blue screen errors article, which is what the steps below follow.

What can trigger it

Microsoft’s page lists the technical causes that produce this bug check.

Cause listed by MicrosoftIn plain terms
A device object is freed with an unfinished power requestA driver removed a device while a power change was still pending
A device object finishes a system power request without calling PoStartNextPowerIrpA driver did not follow the power request rules
A device object blocks a power request for too longOne device stalls the whole power change
A power transition times out waiting on the Plug and Play lockThe power change waited for the device system and gave up
A device fails a directed power transitionA device did not switch power state in time

Microsoft adds that finding the exact cause and writing a fix needs programming experience and access to the faulty module’s source code.

That is why the steps for owners focus on removing changes, updating drivers and checking hardware.

Step 1: undo recent changes

Microsoft says to remove or update any driver or system service you recently added.

Think about what changed just before the first blue screen, such as a new device, a driver update or new software.

The support article adds that if you installed new hardware before the error, you should shut down, remove it and restart.

Step 2: check Device Manager

Right-click Start and open Device Manager.

Look for any device marked with a yellow exclamation point.

Microsoft says to review the event log in that driver’s properties and try updating the driver.

If an update does not help, Microsoft’s support article says to disable or uninstall the device.

Our guide to updating a driver in Windows 11 shows the steps.

Step 3: look at Event Viewer

Microsoft says the System log in Event Viewer may hold critical errors from around the time of the blue screen.

Those entries can name the device or driver responsible.

Write down the name so you know which driver to update, or which device to remove and test.

Step 4: test with power saving off

Because this error involves power transitions, Microsoft says to temporarily disable power saving in Control Panel under Power Options.

Some driver problems involve hibernation or suspend and resume, so this step helps isolate the cause.

If the blue screens stop, a driver is probably failing during a power change, and updating that driver is the next move.

Our guide to changing when the screen and sleep turn off shows where the sleep timers are.

Step 5: run diagnostics and check firmware

Microsoft says to run the hardware diagnostics that your system maker supplies.

It also says to ask the manufacturer for updated system ACPI, BIOS or other firmware.

The same page suggests removing or replacing hardware you recently added, or asking the maker for patches.

Step 6: update Windows and keep free space

Microsoft’s support article says to install updates from Start > Settings > Windows Update and select Check for updates.

It also says to keep roughly 10 to 15 percent of the drive free, because Windows needs space for swap files and other functions.

Our guide to checking for updates in Windows 11 covers the Windows Update page.

If Windows will not start normally

Microsoft says you can try the remaining steps from Safe Mode if the PC will not start normally.

Our guide to starting Windows 11 in Safe Mode covers the routes in more detail.

If nothing else works, Microsoft says to use a system restore point or another recovery option.

Our guide to creating a restore point explains how to make one before problems start.

Stop codeOur guide
VIDEO_TDR_FAILUREVIDEO_TDR_FAILURE blue screen fix
Any other stop codeBlue screen of death errors on Windows 11

Sources

Microsoft Learn: Bug Check 0x9F DRIVER_POWER_STATE_FAILURE. Microsoft Support: Troubleshooting Windows unexpected restarts and stop code errors.

Leave a Reply

Your email address will not be published. Required fields are marked *