How To Fix An Epson Printer Not Scanning To Computer (2026)
When an Epson printer will not scan to your computer over Wi-Fi, the fault is usually in how the computer finds the printer or what blocks it.
Epson’s support pages list a clear set of checks, from restarting the computer to adding the printer by its IP address.
This guide puts those checks in a sensible order and explains what each one is for.
Quick answer: the checks that fix most network scan failures
| Symptom | What Epson says to try |
|---|---|
| Cannot scan from the control panel | Restart the computer after installing the software and allow Event Manager through the firewall |
| Printer not found by Epson Scan 2 | Open Epson Scan 2 Utility, enter the printer’s IP address and click Add |
| Error scanning a large original | Scan again at a lower resolution |
| Epson Scan 2 will not start | Exit, wait a few seconds and reopen; if needed, turn the printer off and on |
| Computer and printer cannot talk on one network | Disable the router’s privacy separator |
Put both devices on the same network
Epson’s first check for the ET-8500 and ET-8550 is that the computer and the product are on the same network, network segment or VLAN.
Epson also says to move the product and your computer or smart device closer to the router or access point.
Restart the computer after installing the software
If you cannot scan from the control panel, Epson says to restart your computer after installing the product software.
Epson’s scanner pages say the same thing for the scanner start button, and add that Epson Scan 2 should be running before you press it.
Allow Event Manager through the firewall
Epson says to make sure your firewall or security software is not blocking the Event Manager program.
Epson also tells you to check the scanning setting assigned in Epson Event Manager.
An older Epson page on scanner buttons adds that the wrong default action in Event Manager can make a button do the wrong thing.
Open Epson Scan 2 Utility
Several of Epson’s fixes happen in the Epson Scan 2 Utility, and its location depends on the system.
| System | Where Epson says to find it |
|---|---|
| Windows 10 | Start menu, then EPSON, then Epson Scan 2 Utility |
| Windows 8.x | Apps screen, then EPSON, then Epson Scan 2 Utility |
| Other Windows versions | Start, All Programs or Programs, EPSON, Epson Scan 2, then Epson Scan 2 Utility |
| Mac | Applications, then Epson Software, then Epson Scan 2 Utility |
Epson’s page lists Windows 10 as its newest Windows entry, so check your version’s own listing if you use a newer one.
Reset the scanner connection
If the connection setting has become faulty, Epson says to reset it in the utility.
- Open Epson Scan 2 Utility.
- Select your product.
- Open the Other tab.
- Click Reset.
Epson also says to check the network connection setting in the same utility.
Add the printer by its IP address
When a firewall prevents discovery, Epson says the utility may not find the printer on its own.
Open Epson Scan 2 Utility, enter the product’s IP address and click Add.
Epson’s scanner pages say to check the address on the control panel, and our guide to an Epson printer after a router change explains why the address can change.
Check the router settings
Epson lists three router-side causes for scans that still fail.
- Firewall or anti-virus software on the router or access point may need to be turned off temporarily.
- A privacy separator that keeps devices apart should be disabled in the router settings.
- A 5 GHz router should run in dual-band mode, with separate names for the 2.4 GHz and 5 GHz bands.
Epson’s example names are Home Network 2.4 GHz and Home Network 5 GHz, and it says your router’s documentation or internet provider can help.
Epson also notes that Epson Scan 2 does not support networks that use only IPv6, so the network must support IPv4.
If the printer is connected by Ethernet
Epson’s wired scanning page lists extra causes for devices that connect through a cable and hub.
| Cause | Epson’s fix |
|---|---|
| Ethernet hub turned off | Confirm the hub is on |
| Hub and scanner powered on in a bad order | Restart the hub, wait about one minute, then check the connection |
| Loose or faulty cable, or hub port | Reseat the cable, or try a different port or cable if the hub light is off |
| Two devices share an IP address | Check each device’s address and give each a unique one |
If the problem remains, Epson says the hub itself may have failed and can be replaced.
Errors and large scans
A few messages have their own fix on Epson’s pages.
| What you see | Epson’s fix |
|---|---|
| Network product is not available | Restart the product |
| Network communication error on a large, high-resolution scan | Scan again at a lower resolution |
| Epson Scan 2 stops while starting | Exit, wait a few seconds, restart it; if it will not restart, turn the product off and on |
The “not available” message can read as though another user is using the scanner, but Epson says it can indicate a communication error.
Document Capture and the scanner button
Epson’s wireless scanner pages say Document Capture Pro on Windows and Document Capture on Mac do not support starting a scan from the scanner button over a wireless network.
For those scanners, Epson says to launch Epson Scan 2 first and scan from there.
The same FAQ notes that Document Capture Pro and Document Capture are not available for the ES-300WR and ES-500WR at all.
If Epson ScanSmart is installed
Epson’s ES-500WR FAQ says that when Epson ScanSmart is installed, the scanner’s start button opens ScanSmart instead.
That applies over USB or wireless, so a scan window you did not expect may simply be ScanSmart.
When to contact Epson support
Epson’s pages do not give a final step beyond the checks above, so if none of them work, contact Epson support for your model.
If the printer itself shows offline, fix that first with our guide to an Epson printer that shows offline.
Sources
Epson pages used: ET-8550 FAQ: I cannot scan over a network, Cannot Scan Over a Network and Cannot Scan Over a Network (5 GHz).