How To Fix A TP-Link Router With No Internet (2026)
A TP-Link router with no internet usually means one of three things: the modem is not delivering a connection, the router is not receiving it, or a setting is wrong.
TP-Link has two support articles for this, one for a router that is not connecting and one for an Internet light that is off or a WAN port that is unplugged.
This guide combines both into one order of checks, starting with the quickest.
Quick answer: what to check first
Log in to the router and look at the Internet IP address on the status page, because it sends you down the right path.
| What you see | What it points to | Where to go |
|---|---|---|
| Internet IP is 0.0.0.0 | The router is not getting a connection from the modem | Path A below |
| Internet IP looks valid but pages will not load | A DNS or routing problem | Path B below |
| Internet light off or a WAN Port Unplugged message | Cable, WAN port or port speed | WAN port steps below |
Start with the basic checks
- Confirm the modem is connected to the router’s WAN or Internet port.
- Confirm your computer is connected to the router’s network.
- Log in to the router’s web management page, go to Advanced, then Status, and note the Internet IP address.
TP-Link also says to wait until the router’s power light and the modem’s lights are solid before testing.
Path A: the Internet IP shows 0.0.0.0
This means the router has no working connection to your provider through the modem.
| Step | What TP-Link says to do |
|---|---|
| 1 | Check the Ethernet cable from the modem is firmly in the WAN or Internet port |
| 2 | Connect a computer straight to the modem, and restart the modem if it has no internet |
| 3 | Clone your computer’s MAC address on the router (Advanced, Network, Internet, MAC Clone, then Save), using a wired connection |
| 4 | Change the router’s LAN IP to a different range such as 192.168.2.1 (Advanced, Network, LAN, then Save) |
| 5 | Restart the modem and router in the TP-Link sequence |
| 6 | Ask your provider whether the connection type is Dynamic IP, PPPoE or Static IP |
If the computer has no internet even when plugged into the modem, contact your provider, because the router is not the cause.
TP-Link says the default LAN address is usually 192.168.0.1 or 192.168.1.1, so changing it is the fix for an address clash with the modem.
The restart order TP-Link gives
- Power off the modem and the router, then wait 1 minute.
- Power on the router first and wait about 2 minutes for a solid power light.
- Power on the modem and wait about 2 minutes for solid lights.
- Wait 1 to 2 more minutes, then test the connection.
TP-Link’s separate slow-internet article restarts the modem first, so if one order does not work, try the other.
Path B: the Internet IP is valid but nothing loads
TP-Link suggests checking whether the IP is a public address with a site such as whatismypublicip.com.
Then set the DNS servers manually under Advanced, Network, DHCP Server.
| DNS field | Value TP-Link gives |
|---|---|
| Primary DNS | 8.8.8.8 |
| Secondary DNS | 8.8.4.4 |
Save, restart the modem and router in the same order as above, and test again.
If it still fails, TP-Link says to factory reset the router and set it up from scratch.
If the Internet light is off or the WAN port seems unplugged
Make sure you are using an RJ45 Ethernet cable and not an RJ11 phone cable.
TP-Link says a working connection turns on both the Ethernet and Internet lights, and some routers with a single light cannot show that split.
The single-light examples it names are the Archer AX3200, AX11000, AX6000 and C5400.
WAN port steps in order
- Check the cable is firmly seated in the WAN port, and replace a worn cable with CAT5E or better.
- Plug a computer directly into the modem to see whether the modem works.
- Move the cable from the modem to a LAN port on the router and watch the Ethernet and Internet lights.
- If both lights come on, the WAN port works and the problem is likely speed negotiation.
- If both stay off, try another cable, then contact TP-Link support.
What the direct modem test tells you
TP-Link’s Internet light article branches based on what happens when a computer is plugged straight into the modem.
| Result | What TP-Link says to do next |
|---|---|
| The computer cannot connect | The modem or provider is the likely cause, so contact your ISP |
| The computer connects and your router has a separate Internet light | The modem works, so test the router’s WAN port with a LAN port |
| Your router has a single light and shows WAN Port Unplugged or Something Is Wrong with the Hardware Connection | Skip to the port negotiation speed setting |
That branching saves time, because replacing a router will not fix a modem that cannot reach the internet.
Keep a note of each result, since TP-Link support asks for them if you need to call.
Set the Internet port negotiation speed
When the WAN port works but the light stays off, TP-Link says to log in and go to Advanced, Internet, Internet Port Negotiation Speed Setting.
Set it to 100 Mbps full duplex, then check whether the Internet light turns on.
TP-Link uses the Archer AX1500 as its example, so the menu name may differ on your model.
Reset the router if nothing works
With the router powered on, TP-Link says to press and hold the Reset button for more than 10 seconds for a hard reset.
A reset erases your custom settings, so you will need to set the router up again afterward.
What to give TP-Link support
| Detail | Why it matters |
|---|---|
| Internet IP on the status page | Shows whether the router has a connection |
| Modem model and cable or DSL type | Identifies the modem side |
| ISP name | Needed for the WAN port case |
| Router model, hardware version, firmware version | Identifies your exact unit |
| Steps already tried and their results | Avoids repeating them |
TP-Link asks for the status page IP, the modem model and type, and the steps you have already tried in the not-connecting article, and adds the ISP name and router versions in the Internet light article.
Related guides and official sources
Other brands follow the same logic, as in our Netgear no-internet guide.
If only speed is the problem, see our guide to slow internet on a TP-Link router.
If a printer lost its connection after a router swap, read our Epson printer router change guide.