How To Fix Slow Internet On A TP-Link Router (2026)
A slow TP-Link router can be caused by the router, the Wi-Fi, the modem or your internet provider, and the fix depends on which one.
TP-Link splits the problem into two cases: slow on both wired and wireless connections, or slow only on Wi-Fi.
This guide follows TP-Link’s support articles in that order, so you can rule out the cheap causes first.
Quick answer: which kind of slow is it?
Test one device on an Ethernet cable first, because the result tells you which row applies.
| What you see | Likely area | First step from TP-Link |
|---|---|---|
| Wired and Wi-Fi are both slow | Modem, cable, provider or router settings | Connect a computer straight to the modem and run a speed test |
| Only Wi-Fi is slow | Wi-Fi signal, channel or width | Test again with the device 6 to 9 feet from the router with nothing in between |
| Speed dropped after swapping in a new router | Provider still tied to the old router | Clone a MAC address onto the new router |
Step 1: test speed directly through the modem
- Disconnect the TP-Link router from the modem.
- Connect your computer to the modem with an Ethernet cable.
- Run an internet speed test in your browser.
If the speed matches what you get through the router, TP-Link says the problem is the modem or the internet provider rather than the router.
In that case, contact your provider instead of changing router settings.
Step 2: restart the modem, then the router
TP-Link gives a specific order for this restart.
- Unplug the modem and the router.
- Wait 2 to 3 minutes.
- Power on the modem first and wait until it is fully connected.
- Power on the TP-Link router.
Step 3: swap the cable between modem and router
A worn or low-grade cable can hold the connection back.
TP-Link recommends replacing the Ethernet cable from the modem to the router, and says Cat6 or higher is the one to use.
Step 4: clone a MAC address after replacing a router
If speeds dropped after you installed a new TP-Link router, your provider may still be tied to the old router’s MAC address.
TP-Link says to clone either your computer’s MAC address or the old router’s MAC address onto the new router.
In TP-Link’s router setup article, the setting is under Advanced, Network, Internet, in the MAC Clone section, where you pick the option to use your current computer’s MAC address and click Save.
Use a wired connection for this step, and expect the menu to look slightly different on some models.
If only Wi-Fi is slow
Start by retesting with a clear path between the router and your device.
- Place the router and the test device 6 to 9 feet apart.
- Remove walls, furniture and other barriers between them.
- Keep both on the same horizontal plane, for example both on a table rather than one on the floor.
If speed is fine at that range, the problem is signal strength or interference at your usual spot, not the internet service.
Change the wireless channel and channel width
TP-Link’s slow-internet article suggests these channel widths when only Wi-Fi is slow.
| Band | Channel width TP-Link suggests |
|---|---|
| 2.4 GHz | 40 MHz |
| 5 GHz | 80 MHz or 160 MHz |
TP-Link’s separate Wi-Fi settings guide adds that you should leave Channel and Channel Width on Auto unless you have interference from nearby networks.
Treat the width values as something to try when Auto is not performing, and note your original settings first.
Which fixes apply to your case
TP-Link’s article lists different steps for each case, and QoS and Parental Controls appear in both.
| Fix | Both wired and Wi-Fi slow | Only Wi-Fi slow |
|---|---|---|
| Test through the modem | Yes | Not listed |
| Restart modem, then router | Yes | Not listed |
| Replace the modem-to-router cable | Yes | Not listed |
| Clone a MAC address | Yes, after replacing a router | Not listed |
| Clear 6 to 9 foot retest | Not listed | Yes |
| Change channel and width | Not listed | Yes |
| Turn off QoS and Parental Controls | Yes | Yes |
Work down the column that matches your symptom and stop as soon as speeds return.
Run the same speed test each time so you can tell whether a change helped.
Where the Wi-Fi settings live
| Method | Path (per TP-Link) |
|---|---|
| Web page, most routers | Advanced, then Wireless, then Wireless Settings, then Save |
| Web page, Wi-Fi 8 routers | Wi-Fi, then Main Network, then 2.4/5/6GHz Advanced Settings |
| Tether app | More, then Wi-Fi Settings, pick the band, then Advanced Settings |
Not every model supports every width, so the options you see on your router may be shorter than the list above.
How to log in to change settings
Open tplinkwifi.net or 192.168.0.1 in the address bar of Chrome, Firefox or Edge while connected to the router.
TP-Link says typing the address into a search bar will not reach the login page, and that 192.168.1.1 is another address to try.
TP-Link also says a VPN, a proxy or a browser extension can block the router’s local address, so turn those off if the page will not open.
TP-Link recommends a wired connection when you change wireless settings or update firmware, because changing Wi-Fi settings over Wi-Fi can drop your own session.
The Tether app is the alternative to the browser login if you prefer to work from your phone.
Turn off QoS and Parental Controls
TP-Link lists QoS and Parental Controls as settings that can throttle devices, for both the wired and Wi-Fi cases.
For Parental Controls on a web interface, go to Advanced, then Parental Controls, and use the trash can icon to delete any profiles listed.
TP-Link uses the Archer A7 as its example, and says the Tether app and ISP-customized modem routers have their own articles.
QoS has its own TP-Link article, so follow that for your model rather than guessing the menu.
Check router placement and heat
TP-Link warns that a router that is covered, in a confined space or in direct sunlight can overheat and slow down.
Move it to an open, shaded spot and see whether speeds recover.
Related guides and official sources
If the router loses the connection completely instead of slowing down, read our no-internet router guide for the same modem test.
Turning off a router feature that weakens security is covered in our WPS guide.
- TP-Link: fixes for slow internet on any router
- TP-Link: change Wi-Fi settings on a router
- TP-Link: router not connecting to the internet
If speeds are still slow
TP-Link says to contact its Technical Support for a more in-depth diagnosis when these steps do not help.