|

How To Install The Samsung NVMe Driver On Windows (2026)

Samsung publishes its own NVMe driver for some of its older NVMe SSDs.

The driver is a small download from Samsung, and it installs like any other Windows program.

This guide covers which drives it supports, how to install it, how to confirm it loaded, and why Windows sometimes refuses to load it.

Quick answer: install the Samsung NVMe driver

ItemWhat Samsung says
Driver versionSamsung NVMe Driver 3.3 (file Samsung_NVM_Express_Driver_3.3.exe, 4.72 MB)
Supported drives970 PRO, 970 EVO, 970 EVO Plus, 960 PRO, 960 EVO, 950 PRO
Supported WindowsWindows 7, Windows 8.1 and Windows 10
Download pagesemiconductor.samsung.com, Consumer Storage, Support, Tools
How to confirm itDevice Manager, Storage controllers, Samsung NVMe Controller

Samsung’s driver page does not list Windows 11, so check the next section before you download anything.

Do you need the Samsung driver?

Samsung lists the driver only for the six drive families in the table above.

Newer Samsung drives such as the 980, 980 PRO, 990 EVO and 990 PRO are not on the driver page.

Samsung’s Magician 9 installation guide says RAPID mode works with an NVMe driver from either Samsung or Microsoft, so the built-in Microsoft driver is also an accepted choice.

Samsung’s troubleshooting FAQ says to install the Samsung NVMe driver when Magician cannot see a drive on Windows 7 without NVMe drivers.

System requirements

Samsung’s installation guide lists a short set of minimums.

RequirementMinimum
ProcessorIntel Haswell Refresh
Memory2 GB RAM
Free disk space50 MB
FirmwareUEFI BIOS v2.3

The guide says to run the installer with administrator rights.

Download the driver

  1. Open Samsung’s Consumer Storage support site and go to the Tools page.
  2. Find the Samsung NVMe Driver entry, which is version 3.3.
  3. Download Samsung_NVM_Express_Driver_3.3.exe.
  4. Back up your data before you install, because Samsung’s guide says users bear full responsibility for data loss.

Install the driver step by step

  1. Double-click Samsung_NVM_Express_Driver_3.3.exe, running it as administrator.
  2. Choose your setup language and click OK.
  3. On the Setup Wizard screen, click Next.
  4. Select I accept the agreement and click Next.
  5. On the Ready to Install screen, click Install.
  6. Choose Yes, restart the computer now, and click Finish.

Samsung recommends the restart, although the wizard also lets you pick No, I will restart the computer later.

Check that the driver is installed

  1. Right-click Start and open Device Manager.
  2. Expand Storage controllers.
  3. Look for Samsung NVMe Controller.

Samsung says that if the entry appears, the installation succeeded.

Our guide to updating a driver in Device Manager shows the same window if you have not used it before.

If Windows will not load the driver

Samsung’s guide says the driver loads only when the SSD sits in a PCIe slot wired to the CPU, or in an M.2 or PCIe slot wired to the PCH.

BIOS settingEffect on the driver
PCH Storage Configuration set to RAID modeWindows cannot load the driver
NAND or Storage Remapping enabledWindows cannot load the driver

Samsung notes that the option name differs between motherboard makers, so check your motherboard manual.

Our guide to opening BIOS or UEFI settings in Windows explains how to reach those options.

Blue screen with secNVMe.sys

Samsung’s troubleshooting FAQ describes a blue screen with the message Failed: secNVMe.sys on a 960 PRO running Windows 10 with Hyper-V.

Samsung’s fix is to download and install the latest Samsung NVMe driver from its consumer storage support page.

If the problem continues, Samsung tells owners to contact a Samsung Authorized Service Center.

Repair or uninstall the driver

Samsung gives two ways to repair or remove the driver.

MethodSteps
Control PanelOpen Programs and Features and select the driver
InstallerRun the installer as administrator and choose Repair or Uninstall

Samsung says Repair tries to fix errors and Uninstall removes the driver.

After the install

Samsung’s Magician 9 guide says the SMART self-test on a 970 EVO Plus needs Samsung NVMe driver 3.3.

Once the driver is in place, you can also check your SSD health in Windows.

What Samsung’s license says

The license covers use only with Samsung SSD products.

Samsung says it may collect device-related technical data for support, research and software upgrades.

The software is provided as is, with no warranty and no promise of updates.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *