How To Fix A Logi Bolt Receiver Not Connecting (2026)
A Logitech mouse or keyboard that uses a Logi Bolt receiver can refuse to connect, drop out or fail to wake the computer.
Logitech has a troubleshooting page for Windows and macOS and a separate page for devices that will not pair.
Here they are combined into one order, from the fastest checks to a full re-pair in Logi Options+.
Quick answer: Logi Bolt symptoms and first fixes
| Symptom | First fix |
|---|---|
| Device cannot connect at all | Plug the receiver directly into a port on the computer |
| Connection keeps dropping | Move the device closer and keep other wireless gadgets away from the receiver |
| Device does not wake the computer | Check the Windows USB port power settings and the battery |
| Device feels laggy or delayed | Check for background updates, then update the firmware |
| Pairing fails in the app | Hold the connect button three seconds and try the verification step again |
These steps are for the Logi Bolt receiver only, because Logitech sends Bluetooth connection problems to a separate troubleshooting page.
What Logi Bolt problems look like
Logitech lists five symptoms for Bolt devices: connection drops, no wake from sleep, lag, delay, and a device that will not connect.
The same page names six likely causes, so you can aim at the one that fits.
| Likely cause | What it means |
|---|---|
| Low battery | The device has too little power to hold a link |
| Hub or KVM switch | The receiver must be plugged directly into the computer |
| Metal surface | A wireless keyboard used on metal can lose signal |
| Radio interference | Wireless speakers and cell phones can interfere |
| Windows USB power settings | A Windows USB port power setting can interfere with the receiver |
| Hardware fault | The device, its batteries or the receiver may be faulty |
Plug the receiver straight into the computer
Logitech states that the receiver must be plugged directly into your computer.
That rules out docks, hubs, extenders, KVM switches and similar devices.
For a pairing failure, Logitech’s other page goes further and says to use a port on the motherboard when the receiver sits behind a hub, an extender or the case.
Try a different port, and a USB 2.0 port
If the first port does not work, try another one.
Logitech also says that if you used a USB 3.0 port, you should switch to a USB 2.0 port.
On Windows, check that the device appears in Devices and Printers after each change.
Move closer and reduce interference
Bring the keyboard or mouse nearer to the receiver.
If the receiver is in the back of a desktop, try a front port.
Keep phones, wireless access points and other wireless electrical devices away from it.
Check the battery
Low battery is the first cause Logitech lists for connection problems.
Charge a rechargeable device, or fit fresh batteries in one that takes them, before you pair again.
Update firmware, then check background updates
If a firmware update is available for the device, install it.
For a mouse, Logitech’s tracking page says to select it in Logi Options+, open Settings and look under Firmware version.
Logitech also asks Windows users to check whether Windows updates are running in the background, since they can cause delay.
Mac users should check for background updates in the same way.
Pair a Logi Bolt keyboard again
Install the Logi Options+ app first.
- Open Logi Options+, click Add Device in the upper-right corner and choose the Logi Bolt receiver option.
- Hold the keyboard connect button for three seconds, until the light blinks rapidly.
- When the app finds the keyboard, click CONNECT beside its name.
- Type the numbers shown in the app on the keyboard and press Enter to verify it.
- Click Continue when the app says the device is connected.
If you type the numbers wrongly, the app reports a failed verification, and you can try again.
Pair a Logi Bolt mouse again
The mouse routine is similar, but you verify it by following the on-screen prompts and not by typing numbers.
- Open Logi Options+, click Add Device and choose the Logi Bolt receiver.
- Hold the mouse connect button for three seconds until the light blinks rapidly.
- Click CONNECT beside the mouse name when it appears.
- Follow the on-screen instructions to verify the mouse.
If verification fails, the app tells you, and you can try connecting again.
Remove the old pairing first
Open Logi Options+ and click the trash can icon next to the device, then click YES, REMOVE.
Logitech recommends removing a device while it is turned on and active, so it unpairs cleanly.
The older Logi Bolt app and Logi Web Connect are also covered by Logitech, but its features have moved to Logi Options+.
Which tool you use matters, because Logitech has retired several older ones.
| Tool | Status according to Logitech |
|---|---|
| Logi Options+ | Recommended for connecting and customizing Bolt devices |
| Logi Bolt app and Logi Web Connect | Still documented, but the app features have moved to Logi Options+ |
| Logitech Options | Reached end of support |
| Unifying Software and SetPoint | No longer supported or maintained |
| Onboard Memory Manager | Out of date, so update it to the latest release |
In the older Logi Bolt app, you unpair a mouse by clicking the X beside it and then YES, UNPAIR.
Test on another computer
Try the device with its receiver on a different computer as the last general step.
If it connects there, the first computer’s port or settings are the cause.
If it fails there too, a hardware fault in the device, batteries or receiver becomes more likely.
When to contact Logitech support
Logitech points to warranty information and a File a Warranty Claim option on its support pages.
Use that route when the device still fails on a second computer.