How To Check If Your PC Supports Wi-Fi 6, 6E Or 7 (2026)
Windows 11 can tell you which Wi-Fi standards your wireless adapter supports, so you can see in a minute whether the PC can use Wi-Fi 6, Wi-Fi 6E or Wi-Fi 7.
The check is one command in Terminal, plus a look at your Wi-Fi properties to see which band you are on right now.
Everything below follows Microsoft’s own support pages on Wi-Fi in Windows.
Quick answer: how to check Wi-Fi 6, 6E and 7 support
| What you want to know | Where to check |
|---|---|
| Does my adapter support Wi-Fi 7 or Wi-Fi 6/6E? | Terminal: netsh wlan show drivers, then Radio types supported |
| Does my adapter support WPA3? | Same command, under Authentication and cipher supported in infrastructure mode |
| Is Windows new enough for Wi-Fi 7? | Windows 11, version 24H2 or later |
| Which band am I using right now? | Settings > Network & internet > Wi-Fi > your network properties > Network band (channel) |
| Does my router support the standard? | The router’s documentation or the maker’s website |
All three parts must support a standard before you get its benefits.
What you need for Wi-Fi 6, 6E or 7
Microsoft lists three requirements for the newer Wi-Fi features.
- A router that supports Wi-Fi 7, Wi-Fi 6/6E and WPA3.
- Windows 11 with the latest updates.
- A wireless adapter that supports Wi-Fi 7, Wi-Fi 6/6E and WPA3.
A newer adapter cannot raise the standard of an older router, so check all three.
Make sure Windows 11 is up to date first
- Select Start, then Settings.
- Select Windows Update.
- Select Check for updates and install what appears.
Microsoft says Wi-Fi 7 requires Windows 11, version 24H2 or later.
Our guides to checking for Windows updates and to checking which Windows version you have cover those steps in more detail.
Check your adapter with netsh wlan show drivers
- Right-click Start and choose Terminal.
- Type the command below and press Enter.
netsh wlan show drivers
Microsoft says you can also run the same command in Command Prompt.
The output lists details about your wireless driver, and two lines matter for this check.
Read the Radio types supported line
| Value you see | What Microsoft says it means |
|---|---|
| 802.11be | The adapter supports Wi-Fi 7 |
| 802.11ax | The adapter supports Wi-Fi 6 or Wi-Fi 6E |
Look for these values next to Radio types supported.
If neither appears, your adapter is older than Wi-Fi 6, so check the PC’s documentation or the maker’s website for what it supports.
Check WPA3 support
In the same output, find Authentication and cipher supported in infrastructure mode.
Look for WPA3 Personal for home networks and WPA3 Enterprise for work networks.
Microsoft says WPA3-Personal gives more resilient password-based authentication, even when passwords are weaker than the usual complexity advice.
Check the router
Your adapter is only one side of the link, so read the router’s documentation or its maker’s website.
Microsoft says to look for a Wi-Fi 7 label when you buy a router.
For a Wi-Fi 6E or Wi-Fi 7 link on the 6 GHz band, Microsoft says you need a Wi-Fi 6E router and a Windows device and adapter drivers that support it.
See which band your PC is using right now
- Open Settings and select Network & internet.
- Select Wi-Fi.
- Open the properties of your connected network.
- Read the value next to Network band (channel).
On a Wi-Fi 7 link, Microsoft says a value that lists more than one band, such as 5 GHz and 6 GHz, means Multi-Link Operation is in use.
Our guide to finding your IP and MAC address uses the same properties page.
What the 2.4, 5 and 6 GHz bands mean
| Band | Strengths | Limits |
|---|---|---|
| 2.4 GHz | Longest range, goes through walls best, works with the most devices | Slower, fewer non-overlapping channels, more congestion from microwaves, cordless phones and Bluetooth |
| 5 GHz | Faster, more non-overlapping channels, less congestion | Shorter range and weaker wall penetration |
| 6 GHz (Wi-Fi 6E) | Best performance close to the router, low congestion, lower latency | Shortest range and weakest wall penetration, and it needs a Wi-Fi 6E router and a supporting adapter |
These are the trade-offs from Microsoft’s page on Wi-Fi and your home layout.
What Wi-Fi 6 and 6E add
- MU-MIMO, which lets multiple devices communicate at the same time.
- Double the potential bandwidth, going from four spatial streams to eight.
- 1024-QAM modulation.
- For Wi-Fi 6E, the 6 GHz band, which adds spectrum that is less crowded.
Microsoft identifies Wi-Fi 6 as IEEE 802.11ax.
What Wi-Fi 7 adds
| Feature | What it does, per Microsoft |
|---|---|
| Multi-Link Operation | Uses the 2.4, 5 and 6 GHz bands at the same time to cut congestion and keep the connection steady |
| 320 MHz channels | Ultra-wide channels in the 6 GHz band that double speed potential, aimed at uses such as AR and VR |
| 4096-QAM | Raises data transmission by 20 percent and improves video streaming and conferencing |
Microsoft says Wi-Fi 7 can reach up to four times the speed of Wi-Fi 6 and 6E, with lower latency, and that results vary by maker and hardware.
It also says Wi-Fi 7 (Enterprise) is not currently supported in Windows 11.
Give each band its own network name
Microsoft suggests giving each band its own network name so you know which one you are connected to.
Some routers combine the bands under one name, and Windows then picks the best available band.
That choice is made on the router, so open its settings page if you want separate names.
WPA3 on mixed networks
If your network has both WPA2 and WPA3 access points, Microsoft says the PC tries WPA3-Personal first.
Smooth roaming between WPA2 and WPA3 access points needs an adapter that supports cross-roaming.
Microsoft also advises avoiding WPA+WPA2 mixed mode where possible, because some older adapters cannot reliably fall back from WPA2 to WPA and may fail to connect.
What the check does not tell you
Microsoft’s page does not describe a direct way to see whether your current connection uses Wi-Fi 6, 6E or 7, or whether it uses WPA3.
The connection-level check it does give is the band value on the properties page, where more than one band means Multi-Link Operation is in use.
The driver check shows what your adapter supports, so read it together with your router’s documentation.
If your network does not appear
- Check the network list for both a 2.4 GHz and a 5 GHz version of your network, and try the other one.
- Open Device Manager, expand Network adapters, and open the adapter’s Properties.
- On the Advanced tab, find Wireless Mode or Band and confirm it allows your network’s frequency.
Microsoft says a 2.4 GHz-only adapter cannot see a 5 GHz-only network.
For drops and other faults, see our guides on Wi-Fi that keeps disconnecting and a missing Wi-Fi option.
Related Windows 11 guides
- How to find your IP and MAC address
- How to connect to a hidden Wi-Fi network
- How to fix Wi-Fi that keeps disconnecting
- How to reset network settings