How To Fix ChargePoint Home Flex Not Connecting To Wi-Fi (2026)
A ChargePoint Home Flex that will not join your Wi-Fi can still charge your car, but its app features stop working.
Most fixes start on your phone and router, and only a few involve the charger settings.
This guide uses ChargePoint’s own Home Flex support pages and stays with steps they list.
Quick answer: what to try first
| Symptom | First thing to try |
|---|---|
| Charger will not connect to Wi-Fi | Test another device on your Wi-Fi, then restart the router |
| You changed your Wi-Fi name or password | Use Reconfigure WiFi in the app’s home charger settings |
| App cannot find the charger during setup | Stand within a few feet with Bluetooth on |
| Weak signal at the charger | Try another install spot or a tested Wi-Fi range extender |
| Red light on the charger | A fault was detected, so follow the fault steps or call support |
Your charger still works without Wi-Fi
ChargePoint says the charger will still charge your car on schedule if Wi-Fi goes down.
Without a schedule, it starts charging when you plug in, even with no connection.
Session data shows up in the app once the connection returns.
To charge immediately during a schedule, unplug and plug the connector back in within a few seconds.
What needs Wi-Fi
| Feature | Needs Wi-Fi |
|---|---|
| Reminders and schedules | Yes, ChargePoint says the charger must be connected to Wi-Fi |
| Activation | Yes, activation connects the charger to your home network |
| Charging on schedule or when plugged in | No |
An unactivated station charges at 16A by default for electrical safety.
Check your router and internet first
- Confirm your internet works by testing another device on the same Wi-Fi.
- Unplug the router, wait a few seconds and plug it back in.
- Make sure the router is connected to the modem and powered on.
- Try the charger connection again.
Reconfigure Wi-Fi after a name or password change
If your network name or password changed, the charger needs the new details.
Open the ChargePoint app and select Reconfigure WiFi from the home charger settings menu.
If it still fails, call ChargePoint support.
Activate or set up the charger again
- Turn on Bluetooth and Wi-Fi on your phone.
- Stand close to the charger.
- Open the ChargePoint app and select Home Charger from the main menu.
- Select Set Up Home Charger.
- Select Activate and follow the in-app instructions.
ChargePoint says an error about not finding the charger usually means you are too far away.
A ChargePoint account is required, and signing up is free.
Also make sure your phone itself has Wi-Fi available at the install location.
If you see the message Unable to add home charger to ChargePoint account, try again, and call support if it keeps happening.
Improve the Wi-Fi signal at the charger
ChargePoint suggests trying another installation spot or using a Wi-Fi range extender.
It lists tested extenders that support 802.11bg, and says AMPED Wireless extenders do not work.
Moving a charger to a new spot is installation work, so ask your electrician if the current location cannot be changed.
What the charger light means
| Light | ChargePoint’s meaning |
|---|---|
| Green | Ready to charge, and blinking green means a schedule is set |
| Blue | Plugged in, and pulsing blue means it is charging |
| White | Not connected to Wi-Fi, and blinking white means activation is needed |
| Red | A problem, so contact support |
A white light is the one that points to a Wi-Fi problem.
Reboot the charger from the app
ChargePoint lists a reboot for schedule or data sync problems.
In the app, go to Home Charger, then Settings, then Reboot Charger, and select OK.
If the light is red
A red light means a fault has been detected and charging is unavailable.
ChargePoint’s page lists these recovery steps once the fault clears.
- Unplug and replug the connector.
- In the app, go to Home Charging, then Settings, then Restore to Factory Default.
If the red light stays on, call ChargePoint support instead of opening the charger.
Check your schedule after it reconnects
Once the charger is back online, open the app and review your schedule.
ChargePoint says you can tap the start and end times to change them.
You can set different schedules for weekdays and weekends.
If the app picks the wrong utility or rate plan, set your own in the app.
If you are not plugged in at the set time, the app sends you a reminder.
Confirm the breaker amperage setting
The charger defaults to 16A until you set the breaker amperage.
In the app, go to Home Charger, then Settings, then Breaker Amperage.
Choose the value that matches your breaker, and ask your electrician for the rating if there is no label.
ChargePoint says the rate from the station to your EV cannot exceed 80% of breaker amperage or the charger’s maximum output.
Adjust the indicator light
ChargePoint says you can change the brightness of the LED and Wi-Fi indicator, including turning them off.
If you turn the light off, you will not see the white or red warnings described above, so check the app for status.
Voice assistants after reconnecting
Alexa needs the station activated first and then the skill enabled in the Amazon Alexa app.
iPhone users can add a Siri shortcut in the ChargePoint app.
ChargePoint says Google Home is not currently supported.
When to call support or an electrician
| Situation | Who to contact |
|---|---|
| Wi-Fi, fault or activation problems that continue | ChargePoint Support at 1-888-758-4389, available 24/7 |
| Unsure of your breaker amperage | An electrician |
| Replacing the charging cable | An electrician, with the breaker switched off first |
| Any question about the installation | An electrician |
Do not open the charger or change its wiring yourself.
Related guides
Our ChargePoint Home Flex review covers the specs and installation.
For public stations, see how to fix ChargePoint not starting a charge.
Tesla owners can read how to fix the Tesla app not connecting to your car.
Sources: ChargePoint Home Flex troubleshooting, features and settings and activating your charger.