How To Reset Your Xbox Series X|S To Factory Settings (2026)
Resetting an Xbox Series X or Series S can fix a console whose system software has gone wrong, and it is also the step to take before you sell or give the console away.
The console offers two reset choices, and picking the wrong one either wipes your game library or leaves a problem in place.
This guide follows Microsoft’s Xbox support pages for the reset menu, the USB flash drive method, and the settings backup that makes setup quicker afterwards.
Quick answer: which Xbox reset to choose
| Option | What it does | Use it when |
|---|---|---|
| Reset and keep my games & apps | Resets the operating system and deletes potentially corrupted data, but leaves your games and apps installed | Troubleshooting, and the one Microsoft says to try first |
| Reset and remove everything | Returns the console to factory settings and deletes all user data and installed content | Selling or gifting the console, or a last resort when troubleshooting |
| Cancel | Backs out of the screen with nothing changed | You are not sure yet |
The reset menu is at Profile & system, Settings, System, Console info, then Reset console.
Read this warning before you reset
Microsoft warns that a factory reset erases all accounts, saved games, settings, and home Xbox associations.
Anything that has not been uploaded to the Xbox network is lost.
The console syncs while it is connected to the network, so if it has been offline for a while, connect it and let it sync before you start.
That warning applies to the full reset, and the keep-my-games option is the gentler route when you are only fixing a fault.
Before you reset: restart the console first
A restart does not erase any of your games or data, so it is worth doing before any reset.
| Method | Steps |
|---|---|
| Power Center | Hold the Xbox button on the controller, select Restart console, then select Restart |
| Guide | Press the Xbox button, then go to Profile & system, Settings, General, Power options, and select Restart now |
| Frozen console | Hold the Xbox button on the front of the console for about 10 seconds until it turns off, then press it again to start |
If the console shows no green boot-up animation, repeat the hold-and-start steps and make sure the console shuts down completely first.
Microsoft also describes a full power cycle: shut the console down, unplug the power cable, wait at least 10 seconds, plug it back in, and press the Xbox button.
Setting the console to Sleep and holding the button to shut down fully switches off Sleep and voice wake-up until the next restart.
If a restart cures the fault, you do not need to reset anything.
Back up your settings before a reset
Microsoft lets you save your account and key system settings to a USB storage device, so setup is quicker after the reset.
The device must be USB 3.0 or faster, 128 GB or larger, and formatted for use with Xbox games and apps.
- Connect the USB storage device to the console.
- Press the Xbox button to open the guide.
- Go to Profile & system, Settings, System, Back up & transfer, then Back up my settings.
- Follow the on-screen instructions to save the backup to the device.
Microsoft lists games among the items the backup does not include, so it saves settings only.
What a settings backup keeps and leaves out
| Included in the backup | Not included |
|---|---|
| Most sign-in and security preferences | Controller sign-in |
| Network name and password | Advanced network settings such as IP, DNS, MAC address and port selection |
| Language, location and time zone | Console name |
| Most power mode and start-up settings | Family accounts and content restrictions |
| My home Xbox | Linked social accounts |
| Games and apps drive, updates and notification settings | Profiles other than the one you are using |
Because content restrictions and family accounts are not backed up, set them up again after the reset.
Reset your Xbox from the settings
- Press the Xbox button to open the guide.
- Go to Profile & system, Settings, System, then Console info.
- Select Reset console.
- On the Reset your console? screen, choose Reset and keep my games & apps, or Reset and remove everything.
Start with the keep option, because Microsoft says it clears out corrupted data without deleting your games or apps.
If a damaged game file is what causes the fault, Microsoft says you may then have to choose Reset and remove everything.
Apply your settings backup after a reset
If you are resetting the console you already own, connect the backup drive before you start and turn the console on.
Then go to Profile & system, Settings, System, Console info, select Reset console, and choose Reset and keep my games & apps.
For a new Xbox, connect the storage device before you switch it on, then follow the setup screens.
For a new console that is already set up, keep the drive connected and run the same keep-my-games reset to apply the backup.
Reset with a USB flash drive when settings will not open
Microsoft provides a flash drive method for a console you cannot get into the settings on.
| Requirement | Detail |
|---|---|
| Drive size | At least 4 GB |
| Drive contents | Empty, with no other files |
| Format | NTFS |
| Reset file | The $SystemUpdate file from the Restore Factory Defaults download, copied to the root of the drive |
| PC needed | A Windows PC with an internet connection |
- Plug the NTFS drive into a Windows PC and download the Restore Factory Defaults file from the Xbox support page.
- Extract the compressed file and copy the $SystemUpdate file to the root of the flash drive.
- Safely remove the drive from the PC.
- Turn the console off, unplug the power cable, and disconnect the ethernet cable if you use one.
- Wait 30 seconds, then plug the power cable back in.
- Plug the flash drive into a USB port on the console.
- Hold the Pair button and the Eject button, then press the Xbox button on the console, and keep holding for 10 to 15 seconds.
- Release when you hear two power-up tones, wait for the console to restart, and remove the drive.
On the Series X, press and hold Pair and Eject together, while on an all-digital console without an Eject button you hold only Pair and press the Xbox button.
What the tones mean
| Sound | Meaning |
|---|---|
| First power-up tone | The USB update was detected |
| Second power-up tone | The file was copied and mounted |
| No two tones after 15 seconds, or two power-down chirps | The step failed, so repeat from the point where you hold the buttons |
After the second tone the console restarts, and you can reconnect the ethernet cable when the setup screens appear.
After the reset
When the console restarts you land in the digital setup experience, which walks you through setup again.
Sign in with your Microsoft account, then reinstall anything that the full reset removed.
If you lose access to your account, see our guide to changing your Microsoft account password.
If the console shuts itself off after the reset, read why an Xbox Series X|S turns off randomly.
When to contact Xbox support
If the console still misbehaves after a reset, Microsoft lists live support through its partner Asurion, available 8am to 8pm Pacific Time for warranty, console and controller issues.
The number on Microsoft’s page is (866) 742-2568, and the Xbox support site also offers a virtual agent chat.
Sources: Microsoft’s reset to factory defaults, back up your settings, and restart or power cycle pages.