How To Use Tesla Traffic-Aware Cruise Control (2026)
You turn on Tesla Traffic-Aware Cruise Control at Controls > Self-Driving, then press the right scroll button on the steering wheel to engage it.
It holds your set speed, and it slows down and speeds up to keep a following distance behind the car ahead.
This guide follows Tesla’s Model 3 owner’s manual page on Traffic-Aware Cruise Control, and menus can differ by trim, build date and software.
Quick answer: how to use Traffic-Aware Cruise Control
| Action | How |
|---|---|
| Turn on | Controls > Self-Driving > Traffic-Aware Cruise Control |
| Engage | Press the right scroll button, then release the accelerator |
| Change the set speed | Roll the right scroll wheel up or down |
| Change the following distance | Press the right scroll button left or right |
| Cancel | Press the right scroll button again or press the brake pedal |
A chime confirms it is active, and the set speed shows in blue while the car is cruising.
Settings to check first
All of these are under Controls > Self-Driving.
| Setting | What it does |
|---|---|
| Set Speed | Choose Speed Limit or Current Speed as the basis when you engage |
| Set Speed Offset | With Speed Limit, pick Fixed (same adjustment on all roads) or Percentage (relative to the detected limit) |
| Self-Driving Activation | Choose Single Click or Double Click, if your car has this setting |
| Green Traffic Light Chime | In the U.S. and Canada, sounds when a red light turns green or the car ahead moves |
Tesla says your car may not have the activation setting, depending on trim, configuration or build date.
How to turn it on and engage it
- Touch Controls, then Self-Driving.
- Touch Traffic-Aware Cruise Control.
- Press the right scroll button on the steering wheel.
- Release the accelerator pedal.
Tesla also says you can turn it on by selecting Autosteer with Self-Driving Activation set to Double Click.
It works between 18 and 85 mph (30 to 140 km/h), and below 18 mph it can engage if a vehicle is detected at least 5 ft (1.5 m) ahead.
It is unavailable when Autosteer is on with Single Click activation, or when Full Self-Driving (Supervised) is enabled.
Set speed and match the speed limit
Roll the right scroll wheel up to raise the set speed and down to lower it.
To match the posted limit, press the speed limit sign on the touchscreen, which includes any offset you set.
The set speed shows gray when available but not engaged, and blue when the car is cruising.
You can press the accelerator to go faster for a moment, and the car returns to the set speed when you let go.
Changes can take a few seconds to take effect.
Following distance
Press the right scroll button left or right to change the following distance.
Each level is a time-based gap, which is how long the car would take to reach the rear bumper of the vehicle ahead.
Level 2 is the closest setting, and the touchscreen shows the level while you adjust it.
Tesla says the setting is kept until you change it.
What the car does while it is active
| Situation | Behavior |
|---|---|
| No car ahead | Holds the set speed |
| Car ahead | Slows and speeds up to keep the gap, up to the set speed |
| Curves | Adjusts speed |
| Much faster than the next lane, or nearby cars slower | Reduces speed; press the accelerator to override |
| Stop-and-go traffic | Stays on through full stops and resumes when traffic moves |
Brake lights come on when the car slows for traffic.
Why the car shows HOLD
At a standstill, the car may go into a HOLD state instead of resuming by itself.
- You have been stopped for 5 minutes.
- A pedestrian is detected.
- The car ahead is suddenly lost from view.
- An obstacle is detected ahead.
To resume, briefly press the accelerator, and a HOLD icon and prompt appear on the touchscreen.
Exits, interchanges and on-ramps
Near a controlled-access highway exit, within 164 ft (50 m), signaling toward the off-ramp makes the car slow down.
Signal from the outermost lane, using the right signal in right-hand traffic regions and the left in left-hand ones.
If you do not take the exit, it resumes the set speed.
On interchanges and off-ramps, the set speed may drop in 5 mph (5 km/h) steps to as low as 25 mph (40 km/h), based on data from other Tesla vehicles.
Press the accelerator if you want to keep your set speed through that interchange.
On on-ramps, the car sets the speed to the highway limit plus any offset.
Tesla warns it may not reduce speed in some cases, such as when data is insufficient.
Overtake acceleration
Briefly engage the turn signal and the car accelerates toward the vehicle ahead without using the accelerator.
It needs a detected vehicle ahead, a clear target lane, and a speed between 45 mph (72 km/h) and your set speed.
It stops when you reach the set speed, the lane change takes too long, you get too close, or you cancel the signal.
What cancels cruise control
| Action | Result |
|---|---|
| Press the right scroll button | Cancels |
| Press the brake pedal | Cancels |
| Exceed 85 mph (140 km/h) | Cancels |
| Shift into Reverse, Park or Neutral | Cancels |
| Open a door, release the driver’s seatbelt, or leave the driver’s seat | Cancels |
| Automatic Emergency Braking event | Cancels |
After it cancels, the speed icon turns gray and the car does not coast.
Regenerative braking slows it, as it does when you lift off the accelerator.
Warnings from Tesla
Tesla states the feature is not a collision warning or avoidance system, so you must stay alert and in control at all times.
If the car seems likely to run a red light or stop sign, the touchscreen shows a warning and a chime sounds, and you must act at once.
That warning does not stop the car, but Traffic Light and Stop Sign Control, if equipped, can stop it automatically.
If the car will not accept the feature at all, check the Tesla software update guide and make sure the car is not in a mode that limits driving, such as Speed Limit Mode.
Sources: Model 3 Owner’s Manual: Traffic-Aware Cruise Control and Model Y Owner’s Manual: Autosteer.