How To Install An M.2 SSD In A PS5 And Format It (2026)
You want more room for PS5 games, and an M.2 SSD in the expansion slot is the storage Sony supports for playing them at full speed.
The drive has to meet Sony’s specs, it needs a heatsink, and the steps differ between the two console model groups.
This guide follows Sony’s own instructions for choosing a drive, fitting it, formatting it and moving games onto it.
Quick answer: what to buy and what to do
| Step | What Sony says |
|---|---|
| Drive type | PCIe Gen4 x4 NVMe M.2 SSD, Key M, Socket 3 |
| Capacity | 250 GB to 8 TB |
| Cooling | A heatsink and heat transfer sheet are required |
| Before you start | Update the console’s system software |
| After fitting | Format the whole drive when the formatting guide appears |
Drive requirements for a PS5
Sony lists a PCIe Gen4 x4 NVMe drive with a Key M, Socket 3 connector as the supported type.
SATA M.2 drives are not supported, so a drive that looks right but runs over SATA will not work.
Sony says a sequential read speed of 5,500 MB/s or faster is recommended, although some games may not match the internal SSD even on a faster drive.
Sony also says it does not guarantee that every drive meeting these specs will work, and it is not responsible for which third-party product you pick.
Size limits for the drive and heatsink
Sony supports five form factors, and the length of the drive has to match one of them.
| Form factor | Length |
|---|---|
| 2230 | 30 mm |
| 2242 | 42 mm |
| 2260 | 60 mm |
| 2280 | 80 mm |
| 22110 | 110 mm |
These sizes include the heat-dissipation structure, with a width of up to 25 mm and a total thickness of up to 11.25 mm.
Of that thickness, up to 8.0 mm can sit above the board and up to 2.45 mm below it.
Single-sided and double-sided drives are both supported.
Why the heatsink matters
Sony states that a heatsink and a heat transfer sheet are required, and that you should never run the drive without a heat-dissipation mechanism.
If your drive already has a built-in heatsink, Sony says not to add another one to it.
Heatsink sizes vary widely, so if yours may exceed the limits above, choose another product or check with the seller.
A slot cover that will not close is a sign that the cooling structure is too large.
Before you open the console
Update the PS5 system software first, then turn the console off and let it cool.
You need a well-lit table and a #1 Phillips (cross-head) screwdriver, and a small flashlight is optional.
Touch a grounded metal object first to discharge static electricity.
Do not power the console on or play with any cover removed.
Check which model group you have
Sony splits the instructions into two groups, so identify yours before you remove anything.
| Model group | How the cover comes off |
|---|---|
| CFI-2000 and CFI-7000 | Remove a triangle cover, then the expansion slot cover |
| CFI-1000 | Remove the base, slide off the main cover, then the expansion slot cover |
Install on a CFI-2000 or CFI-7000 console
- Remove the triangle cover.
- Remove the screw from the expansion slot cover, then remove the cover.
- Remove the screw and spacer, then move the spacer to the position that matches your drive’s length.
- Hold the drive by its edge, line up the notch with the expansion connector and push it in at an upward diagonal angle until it is fully seated.
- Tilt the drive down and fasten it with the screw.
- Refit the expansion slot cover and its screw, then the triangle cover.
- Reconnect the feet, power cord and cables, then turn the console on.
Install on a CFI-1000 console
- Turn the console off, disconnect every cable and device, and let it cool.
- Put it on a flat, protected surface and remove the base.
- Turn it so the PlayStation logo faces down and the power button faces you.
- Lift the top-left corner of the cover, slide it up and to the right, and take it off.
- Remove the screw from the expansion slot cover, then remove the cover.
- Remove the spacer screw and move the spacer to the groove that matches your drive’s length.
- Insert the drive diagonally until it is fully seated, with the board flat on the spacer and the cooling structure clear of it.
- Tilt the drive down and secure it with the screw, making sure the cooling structure does not block the screw.
- Refit the expansion slot cover and its screw, then slide the main cover back on about 2 cm (3/4 inch) from the top edge until it clicks.
- Reconnect the power cord, cables and base, then turn the console on.
Sony warns that a badly seated drive can damage the terminal and the console.
Format the drive
When the console starts, the formatting guide appears, and you follow its prompts.
Formatting is required on first use, and Sony says the entire drive has to be formatted because partial formatting is not supported.
It erases everything on the drive, and you should not switch the console off during formatting or while saving data.
The exception is a drive you move from another PS5, which does not need formatting again.
Use the drive and move games to it
To choose where new downloads go, open Settings, then Storage, then Installation Location.
To move existing games, open your Game Library, highlight a title, press Options and select Move Games and Apps.
Pick any extra titles and select Move, and if a USB drive is also connected, use the Movable to M.2 SSD Storage tab.
To manage the drive afterwards, go to Settings, then Storage, then M.2 SSD Storage.
A single game’s data has to sit in one location, so you cannot split one game across drives.
If a game stutters on the M.2 drive
Sony suggests pressing the PS button and pausing any downloads or uploads in the control center.
For a disc game, wait until the installation has fully finished.
If the problem continues, move that game back to internal console storage.
Sony also says Host Memory Buffer (HMB) is not supported, so drives that rely on it may run slower than expected.
Removing the drive, repairs and warranty
Remove the M.2 SSD before you send the console in for repair.
Sony says the warranty is generally unaffected when you install a drive that meets its specs and follow the instructions, but damage from incorrect installation is not covered.
To use the drive in another PS5, remove it safely, fit it in the new console and sign in to the same account on both consoles.
Related PS5 storage guides
If a game will not install because of space, see our guide to the PS5 not enough space error CE-100028-1.
For a launch-week example, read what to delete and how to add storage for GTA 6 on PS5.
If your console misbehaves after a software update, try PS5 games crashing after a system update and a stuck or failed PS5 update.
Source: PlayStation Support: How to add an M.2 SSD to a PS5 console.