Fix Elgato Facecam USB3-REQUIRED-FOR-FACECAM Error (2026)
The Elgato Facecam shows “USB3-REQUIRED-FOR-FACECAM” when it detects a connection slower than USB 3.0.
The fix is almost always the port, the cable or the USB controller driver, not the camera itself.
This guide follows Elgato’s own support articles, in the order that is quickest to test.
Quick answer: what to try first
Work down this table and test the camera after each change.
| Step | What to do | Why it helps |
|---|---|---|
| 1 | Plug the Facecam into a USB 3.x port on the computer itself | Ports are usually blue, cyan or red; USB 2.0 triggers the error |
| 2 | Use the cable that came with the Facecam | Other cables may not meet the USB 3.0 standard |
| 3 | Skip hubs, monitors and other go-betweens | Connect straight to the computer |
| 4 | Install the latest USB 3.x controller drivers | Get them from your motherboard or laptop maker |
| 5 | Remove the Facecam under Other devices and restart | Windows reinstalls the driver at startup |
What the USB3-REQUIRED-FOR-FACECAM error means
The Facecam needs a USB 3.x (or higher) connection to work.
Elgato says the error appears when the camera is connected to a USB 2.0 or lower port.
Elgato notes that the Facecam sends uncompressed video, which uses a lot of USB bandwidth.
A port that looks like USB 3.0 can still behave like USB 2.0 if the cable or a hub in the chain is slower.
Use a USB 3.x port
Look for a port with a blue, cyan or red inside, since those colours usually mark USB 3.x.
Elgato’s separate USB 3.0 article adds that teal ports (USB 3.1) also work.
It also says red or yellow ports that support USB 3.0 or 3.1 with power delivery are acceptable.
- Unplug the Facecam and plug it back in so it is fully seated.
- Move it to a different USB 3.x port on the computer.
- Test the camera in Camera Hub.
A loose connection can cause the same communication problem, so reseat the plug before anything else.
How to tell the ports apart
Use this table to read the ports on your computer.
| Port colour | What Elgato says |
|---|---|
| Blue | Usually USB 3.0 |
| Teal or cyan | USB 3.1 or 3.2, backward compatible with USB 3.0 |
| Red or yellow | Works if it supports USB 3.0 or 3.1 with power delivery |
Colours vary by maker, so check your motherboard or laptop manual if you are unsure.
Check the USB cable
Use the cable that shipped with the Facecam.
Elgato warns that other cables may not meet the USB 3.0 standard.
Cables bundled with phones, especially USB-C to USB-C cables, may support only USB 2.0.
If you must replace the cable, Elgato’s frozen-video guide asks for USB 3.1 Gen 1 (USB 3.0) or higher at 5 Gbps or more.
Plug in directly, without a hub
Connect the Facecam straight to the computer, not through a hub, monitor or other intermediary.
If you have to use a hub, Elgato says it must be USB 3.0 compatible.
A dock can behave like a hub, so test directly first.
If direct works and the dock does not, see our guide to a docking station not working in Windows 11.
Update the USB controller drivers
Install the latest USB 3.x controller drivers from your motherboard or laptop manufacturer.
Intel controllers use Microsoft’s built-in drivers, which you can update through Windows optional updates.
Elgato notes that some controllers use basic Microsoft drivers that cannot be reinstalled, and other controllers usually work fine with them.
- Open Settings, then Windows Update.
- Open Advanced options, then Optional updates.
- Install any USB controller or chipset driver offered, then restart.
Remove the Facecam and let Windows reinstall it
Elgato’s reset for a bad driver installation is short.
- Open Settings, then Devices.
- Find the Elgato Facecam under Other devices.
- Choose Remove Device.
- Restart the computer.
The driver installs again automatically at startup.
Afterwards, open Camera Hub to confirm the camera appears.
Try every USB 3.0 port
Motherboards often have more than one USB controller, so each port can behave differently.
USB 3.1 and 3.2 ports are backward compatible with USB 3.0 devices and are fine to try.
Test front-panel ports as well as the ports on the back of a desktop.
If one port works, leave the Facecam there.
Check USB bandwidth
Too many devices on one hub or controller can use up the available bandwidth.
Each controller typically serves a pair of ports.
Capture cards, external drives and webcams sharing a pair can cause problems.
Unplug other devices or move them to different ports and test again.
If the Facecam then works but another device drops out, see USB keeps disconnecting in Windows 11.
If the video freezes after the error is gone
Elgato says the Facecam defaults to Automatic transfer mode and picks Bulk or Isochronous itself.
| System | Automatic mode uses |
|---|---|
| Windows PC | Bulk |
| M1 Mac | Isochronous |
| Intel Mac | Bulk |
| Microsoft Surface | Isochronous |
To override it, install Camera Hub 1.2.2 or later and update the Facecam to firmware 4.06 or later.
Hold Ctrl (Windows) or Command (Mac), click the Facecam settings in Camera Hub, and pick Bulk or Isochronous.
The camera disconnects briefly while the mode changes.
Elgato suggests Isochronous as the first try for freezing, and says the Facecam Pro can change mode on its release firmware.
You can also lower the resolution or frame rate in the app you use, for example 1080p60 to 720p60, to cut bandwidth.
If Windows does not see any camera
If the camera does not appear in apps at all, check the Windows camera permissions.
Our guide to camera not working on Windows 11 covers that.
When to contact Elgato support
If the error stays after every step above, use the support widget on Elgato’s article pages.
Tell them which port, cable and computer you tested, so they can skip the basics.
Sources: Elgato: USB3-REQUIRED-FOR-FACECAM, Facecam requires USB 3.0, Frozen video troubleshooting and USB transfer mode.