How To Fix USB Keeps Disconnecting In Windows 11 (2026)
A USB mouse, drive or webcam that keeps dropping out and reconnecting is usually short of power or being put to sleep by Windows.
Dell lists a device that repeatedly connects and disconnects on its own as one of the standard USB symptoms.
This guide uses Dell and Microsoft documentation to work from the cheapest checks to the settings that matter most.
Quick answer: match the pattern to the fix
| Pattern | Likely cause | Start with |
|---|---|---|
| Drive or webcam drops behind a hub | The hub cannot supply enough power | Plug it straight into the PC or use a powered hub |
| Drops after sitting idle | Windows is powering the port down | Turn off the Power Management checkbox |
| Drops only on battery | The PC is limiting power | Plug the PC into mains power |
| Power Surge on the USB Port message | The device pulls more than the port can give | Follow the power steps below |
| Only one device drops | Faulty cable or device | Test it on another computer |
Rule out the cable and the device
Swap in a different cable first, because a loose or damaged connector can break the connection for a moment.
Then plug the same device into another computer to see whether the drop-outs follow the device.
If the drop-outs follow the device to every port, Dell treats the device or cable as the suspect and moves on to the software steps.
Remove hubs and connect directly
Microsoft advises connecting a device straight to the PC rather than through a hub or dock when you troubleshoot.
It also suggests unplugging any USB devices you do not need, because each one shares the available power.
If it holds steady when plugged in directly, the hub or dock is where to look next.
Give the device enough power
Dell recommends a USB hub with its own AC adapter for devices that draw more power, such as external hard drives, some webcams and charging accessories.
- Plug the hub into a wall outlet.
- Connect the hub to the computer.
- Connect the device to the hub instead of the PC.
Microsoft adds two habits for a device that needs more power: connect its own power source if it has one, and keep the PC plugged in rather than on battery.
Understand the Power Surge on the USB Port message
Dell says this message appears when a device draws more power than the port can supply.
| Cause listed by Dell | What it means for you |
|---|---|
| Device needs more power than the port gives | Use a powered hub or the device power supply |
| Faulty device or cable | Try another cable, then another computer |
| Outdated or corrupted USB controller drivers | Reinstall the controllers |
| Power saving put the port to sleep | Change the power settings below |
Dell also suggests running the Hardware and Devices troubleshooter and updating the BIOS with SupportAssist if the message keeps returning.
Stop Windows sleeping the device
- Open Device Manager from the Start button.
- Expand Universal Serial Bus controllers.
- Open the Properties of each USB Root Hub.
- On the Power Management tab, clear the box that lets the computer turn the device off to save power.
- Click OK on each one and restart.
Turn off USB selective suspend
- Open Control Panel, then Hardware and Sound, then Power Options.
- Select Change plan settings for your active plan, then Change advanced power settings.
- Expand USB settings, then USB selective suspend setting.
- Set both On battery and Plugged in to Disabled.
- Select Apply, then OK, and restart.
Dell notes this may slightly raise power use on a laptop, and you can set it back to Enabled later.
| Enabled (default) | Disabled | |
|---|---|---|
| What Windows does | Suspends an individual idle port without touching the others | Keeps idle ports powered |
| Battery life | Idle devices draw less power | Slightly higher drain on laptops |
| Microsoft position | Strongly recommended to leave on | Use only to test a drop-out problem |
Reinstall the USB controllers
- Unplug the device.
- In Device Manager, uninstall every entry under Universal Serial Bus controllers.
- Restart so Windows reinstalls them.
- Reconnect the device and watch for another drop.
Match the error message to the next step
| Message Dell lists | Where to go next |
|---|---|
| USB Device Not Recognized | Check Device Manager, then reinstall the controllers |
| Power Surge on the USB Port | Use the power steps above |
| Device Descriptor Request Failed | Work through the cable, power and controller steps in this guide |
| This device cannot start (Code 10) | Read the error code in the device Properties |
To read a code, open the device in Device Manager, select Properties and look under Device status.
Microsoft says to look up any code except Code 28 in its Error codes in Device Manager article, since Code 28 only means the driver is not installed.
Run the Hardware and Devices troubleshooter
- Open Start, then Settings, then System, then Troubleshoot.
- Select Other troubleshooters.
- Choose Run beside Hardware and Devices and follow the prompts.
Restart afterwards and reconnect the device to see whether the drop-outs return.
Install updates and a BIOS update
Select Start, then Settings, then Windows Update, and choose Check for updates.
On a Dell laptop, plug the charger in, open SupportAssist and select Check for updates to see whether a BIOS update is waiting.
Dell says to restart and reconnect the device after any BIOS update before you test again.
Test in Safe Mode for a software conflict
Dell explains that Safe Mode loads only essential drivers, so a USB controller that behaves there points to a third-party app or driver.
To get there, go to Settings, System, Recovery, choose Restart now beside Advanced startup, then pick Troubleshoot, Advanced options and Startup Settings.
If the dropping port is USB-C
Microsoft says to connect the device to a USB-C port that supports its features, and to avoid hubs and docks.
| Windows notification | Microsoft fix |
|---|---|
| USB device might need more power | Connect its power source, plug in the PC, unplug unused devices |
| Use different USB port | Move it to another USB-C port that supports its features |
| USB4 device functionality might be limited | Use the maker cable or a certified USB4 cable |
To see these alerts, search for usb, open USB settings and turn on Connection notifications.
When to contact support
If the device works on another port but not the original, Dell says the port may be faulty and points you to Dell Support.
Dell also offers a USB diagnostics page that scans and tests the ports.
Related guides: safely ejecting a USB drive, checking a USB port power output, USB-C errors and USB ports that do not respond at all.
Sources: Dell Power Surge on the USB Port, Dell advanced USB troubleshooting, Microsoft Fix USB-C problems and Microsoft USB selective suspend.