GTA 6 Black Screen Or No Signal On PS5 And Xbox: Fixes (2026)
Grand Theft Auto VI starts, and then the TV goes black, shows “no signal” or never gets past a blank screen.
Neither Sony nor Rockstar lists a GTA 6 black-screen bug, so the fix is the video-signal checks that the console makers publish.
This guide follows Sony’s and Microsoft’s own pages in order, from the cable to Safe Mode on PS5 and the video modes on Xbox.
Quick answer: what to try first
| What you see | Try first |
|---|---|
| Black screen on PS5 | Cable, HDMI port and input, then a full power cycle with a 20-minute wait |
| PS5 screen stays blank and you cannot reach Settings | Safe Mode, then Change Video Output |
| PS5 picture flickers at 4K | Video Transfer Rate set to -1 or -2 |
| Black screen or no HDR on Xbox | 4K TV details, then clear Allow HDR10 and Auto HDR to test |
| PS5 picture is cut off at the edges | Adjust Display Area |
Whose problem this is
Sony’s Grand Theft Auto VI support page covers downloads, launching, missing bonuses and the Vintage Vice City Pack.
That page does not mention black screens, no picture or HDR, and it lists no error codes.
Rockstar’s HDR troubleshooting article applies to its games in general and does not name GTA VI either.
If you see advice online to turn HDR off, that is a player suggestion that neither Sony nor Rockstar publishes.
Until a vendor says otherwise, treat a black screen as a signal problem between the console, the cable and the TV.
Check the cable, port and input
Sony says to make sure the HDMI cable is firmly connected at both the console and the screen.
Try a different cable if you have one, try a different HDMI port on the screen, and confirm the screen is set to the right HDMI input.
Connect straight to the screen
Plug the console directly into the screen’s HDMI port, as Sony advises for PS5.
Unplug soundbars, home theater systems and capture devices, which Sony names as possible causes.
Microsoft gives the same advice for Xbox: connect the console to the TV first, then send sound to a receiver or soundbar through ARC or eARC.
Power cycle the screen and the console
Sony’s steps are to turn off the screen and the console completely and unplug both power cables.
Wait 20 minutes, reconnect everything and turn it back on.
Sony also says to check that the screen runs its latest firmware, and to read its manual for settings needed by high-resolution signals.
PS5: see what signal the console sends
If you can reach the menus, open Settings, then Screen and Video, then Video Output.
Information for the Connected HDMI Device shows the resolution, the VRR status and the HDR status, and Current Video Output Signal shows what the console is sending now.
PS5: Change Video Output in Safe Mode
- Turn off the console by holding the power button for three seconds.
- Press and hold the power button again and release it after the second beep, about seven seconds after the first.
- Connect a controller with a USB cable and press the PS button.
| Safe Mode option | What Sony says it does |
|---|---|
| Change Video Output | Changes the resolution or HDCP mode, which can help with blank screens |
| Update System Software | Updates by direct download or from a USB drive |
| Restore Default Settings | Returns settings to default; games, apps, screenshots, clips and saved data are kept |
| Reset PS5 | Deletes all user data, so it is not a fix to reach for here |
Sony does not explain what each Change Video Output setting alters, so try one change and test the picture.
PS5: 120 Hz, VRR and Video Transfer Rate
These options sit under Settings, then Screen and Video, then Video Output.
| Setting | Sony’s note |
|---|---|
| 120 Hz Output | Turn it off if you see video problems on a monitor or another display |
| Apply to Unsupported Games (VRR) | Turn it off if you notice unexpected behavior |
| Video Transfer Rate | If the screen flickers, try -1 or -2 to limit the output |
| Resolution | Use Auto or 2160p when checking 4K 120 Hz |
For a TV that claims 4K 120 Hz, Sony’s checklist asks about the latest TV firmware, the included or an Ultra High Speed cable, a direct connection and an HDMI 2.1 port.
PS5: HDR settings
Open Settings, then Screen and Video, then Video Output, then HDR.
Always On converts games and apps that are not HDR-compatible to HDR output.
On When Supported shows those games and apps in standard dynamic range instead.
Sony’s HDR page describes no way to turn HDR off completely; if HDR will not turn on, it points to the PlayStation Repairs diagnostic tool.
Xbox: check 4K TV details
Microsoft’s Xbox Wire guide, published in November 2020, says to open the guide with the Xbox button and go to Settings, General, TV & Display Options, then 4K TV details.
You should see green checkmarks for each feature, and if you do not, the guide says to troubleshoot.
It also says some TVs support HDMI 2.1 on only certain ports, so connect to each port in turn and check that screen again.
Xbox: switch features off to test
| Test | Path in the Xbox Wire guide |
|---|---|
| Turn off 4K | Settings, General, TV & Display Options, Advanced, Video modes, then clear Allow 4K |
| Turn off HDR | Same Video modes page, then clear Allow HDR10 and Auto HDR |
| Turn off VRR | Same Video modes page, then clear Allow Variable Refresh Rate |
| Lower the refresh rate | Settings, General, TV & Display Options, Refresh rate, then 60 Hz |
| Re-detect the display | Settings, Display & sound, Auto-detect; 4K is unavailable if HDMI or DVI is picked by hand |
The guide dates from 2020, so a menu name may differ; it also says that if some content will not play, you should confirm the TV supports HDCP 2.2 and that it is enabled.
TV settings that can break HDR
Rockstar’s article says to confirm that your display supports HDR and that HDR is switched on in its settings.
It also says to turn on Game Mode, turn off picture enhancements such as AI enhancement or Smart, Dynamic and Adaptive modes, and turn off Dynamic Tone Mapping.
If your display offers HGIG, Rockstar says to enable it.
| TV brand | Setting named in the Xbox Wire guide |
|---|---|
| Samsung | Settings, Picture, Expert Settings, HDMI UHD Color, On |
| LG | Settings, All Settings, General, HDMI ULTRA HD Deep Color, enabled on the port in use |
| Sony Bravia | Home, Settings, External Inputs, HDMI signal format, Enhanced format |
When to contact support
For an HDMI cable that does not work, a pixelated image, no image or no HDR, Sony directs PS5 owners to its PlayStation Repairs diagnostic tool.
The sources used here give no repair route for Xbox, so start from Microsoft’s Xbox support site.
Related guides
- GTA 6 graphics modes on PS5, PS5 Pro and Xbox
- GTA 6 not starting or crashing on PS5
- GTA 6 not starting or crashing on Xbox Series X|S