|

How To Fix Ethernet Not Working In Windows 11 (2026)

When Ethernet is not working in Windows 11, the PC shows no connection or no internet even though a cable is plugged in.

Microsoft’s Ethernet guide starts with the cable and router, then moves to network commands, the adapter driver and a network reset.

This guide follows that order so you fix the cheap problems before touching drivers.

Quick answer: fix Ethernet in the right order

OrderFixWhere
1Check the cable and the router portRouter and PC
2Restart the modem and routerPower cords
3Check the connection statusSettings > Network & internet
4Run the network commandsCommand Prompt (administrator)
5Uninstall the Ethernet adapter driverDevice Manager > Network adapters
6Network resetSettings > Network & internet > Advanced network settings

Check the cable and the router port

Make sure the cable is pushed in firmly at both the router and the PC.

Microsoft says to use one of the router’s Ethernet (LAN) ports, not the Internet port that connects to the modem.

If you have a spare cable, swap it in, because a failed cable looks exactly like a broken adapter.

If your PC has no Ethernet port, a USB-to-Ethernet adapter is the option Microsoft mentions.

Restart the modem and router

  1. Unplug the router’s power.
  2. Unplug the modem’s power, and if it has a backup battery and the lights stay on, remove the battery.
  3. Wait about 30 seconds, then put any battery back in.
  4. Plug the modem in and wait for its lights to stop blinking.
  5. Plug the router in and wait a few minutes for both to start fully.
  6. Try the Ethernet connection again.

If you have a single combined cable modem and Wi-Fi router, restart only that one device.

Check the connection status in Settings

Open Settings > Network & internet and look at the Ethernet entry.

Status shownWhat to do
ConnectedThe link is up, so test a website, and if pages fail move to the commands below
Action neededSelect Ethernet to open its settings and review the connection
Not listedCheck the cable, then check the adapter in Device Manager

Microsoft’s own wording covers Connected and Action needed, so the third row is simply the next place to look.

Try Wi-Fi to find the faulty part

If your router offers Wi-Fi, connect to it wirelessly for a moment.

If Wi-Fi works, the router and your internet service are fine and the fault is the cable, the port or the Ethernet adapter on the PC.

If you have a second Windows PC and a USB-to-Ethernet adapter, Microsoft suggests plugging that PC into the same network.

If the second PC connects, the first PC is the problem, and if neither connects the issue may be the router, your internet provider or the adapter.

Run the network commands

Search for Command prompt, select Run as administrator, then select Yes.

Run these commands in order, pressing Enter after each one.

netsh winsock reset
netsh int ip reset
ipconfig /release
ipconfig /renew
ipconfig /flushdns
CommandWhat it does
netsh winsock resetResets the Windows network socket settings
netsh int ip resetResets the TCP/IP settings
ipconfig /releaseGives up the current IP address
ipconfig /renewAsks the router for a new IP address
ipconfig /flushdnsClears the saved DNS lookups

Restart the PC afterward, because the two reset commands take full effect after a restart.

Check how the IP address is assigned

Microsoft says you can see your IP address under Settings > Network & internet > Ethernet, where it is listed as IPv4 address.

Select your Ethernet network and look at IP assignment, where Microsoft recommends Automatic (DHCP) over Manual.

Microsoft’s Wi-Fi guide adds that an address starting with 169.254 means the PC did not get one from the router, and the fix is to turn on DHCP on the router.

Ping the router to see where the break is

Microsoft’s Wi-Fi guide describes a quick ping test that works the same way over a cable.

  1. In an administrator Command Prompt, run ipconfig and note the Default gateway address.
  2. Run ping followed by that address.

If you get replies, the PC reaches the router, so the fault may be the modem or your internet provider, and you should check for an outage or contact the provider.

If you get no replies, the PC is not reaching the router at all, so go back to the cable, the router port and the adapter driver.

Uninstall the Ethernet adapter driver

Microsoft says to download the latest network adapter driver from your PC maker’s website first, using another PC and a USB drive if yours is offline.

  1. Open Device Manager from the taskbar search.
  2. Expand Network adapters and select your Ethernet adapter.
  3. Select Uninstall device.
  4. Tick Attempt to remove the driver for this device, then select Uninstall.
  5. Select Start > Power > Restart.

Windows should reinstall the driver automatically, and if it does not, install the driver you downloaded.

Microsoft singles this fix out for a problem that started after a recent update.

Use network reset as a last resort

  1. Go to Start > Settings > Network & internet > Advanced network settings > Network reset.
  2. Select Reset now, then Yes.
  3. Wait for the PC to restart and test the connection.

Network reset removes your network adapters and their settings, and Windows reinstalls them with defaults.

Afterward you may need to reinstall VPN clients or Hyper-V virtual switches, and the network may go back to the Public profile.

See our step-by-step guide to resetting network settings in Windows 11 before you start.

Set the network profile after a reset

Go to Settings > Network & internet > Ethernet, select your network and open Network profile type.

Microsoft marks Public network as the recommended choice, while Private network lets other devices find your PC for file and printer sharing.

Our guide to switching a public network to private shows the same setting in more detail.

If Ethernet connects but is slow or still has no internet

A link that shows Connected but loads nothing points to DNS or the router, so try changing the DNS server next.

If the cable works but speeds stop at 100 Mbps, read how to fix Ethernet speed capped at 100 Mbps.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *