|

How To Fix USB Ports Not Working In Windows 11 (2026)

When a USB port stops responding, the mouse, drive or phone you plug into it simply does nothing.

The cause is usually a worn cable, a power-saving setting or a driver that needs a reset, and only rarely a dead port.

These steps follow the guidance Dell and Microsoft publish for Windows 11, in the order that is quickest to try.

Quick answer: what to try first

What you seeTry this first
No device works in any portRestart, then test the device on another PC
Works in one port but not anotherClean the port, then run the USB port diagnostics
Yellow exclamation mark in Device ManagerUninstall the device and restart so Windows reinstalls it
Stopped after an updateCheck for updates, then try System Restore
Dead before Windows even startsCheck the USB setting in BIOS

Check the port, cable and device

Look into the port and at the plug for bent pins, dust or debris.

Dell advises short bursts of compressed air with the can held upright, and never water or liquid cleaners.

Plug the same device into another computer, because that shows whether the device itself is the problem.

If the cable feels loose or wiggles in the port, try a different cable.

Restart and try a different port

A restart refreshes the system and can install missing USB drivers, according to Dell.

On a desktop, unplug everything except the keyboard and mouse before you test.

Then move the device to another port, since a device that works elsewhere points at the original port.

USB 3.0 ports often have a blue insert or an SS mark, and Thunderbolt ports are marked with a lightning bolt.

Read the Device Manager symbols

Press Windows + R, type devmgmt.msc, press Enter, and expand Universal Serial Bus controllers.

SymbolMeaningWhat Dell says to do
Black down arrowThe device is disabledRight-click it and select Enable device
Yellow exclamation markThe device has a problem but may partly workTry another port, remove hubs, select Uninstall device, then restart
Red XThe device is present but disabled, with no driver loadedSelect Enable device, or Uninstall device and restart
Yellow question markUnknown device with missing driversConnect it directly, then Update driver and Search automatically

If a box named Delete the driver software for this device appears, Dell says to tick it before you select OK.

You can also open the device Properties and read the error code under Device status, which Microsoft says to look up in its Error codes in Device Manager article.

The one exception is Code 28, which only means the driver is not installed yet.

Run the Hardware and Devices troubleshooter

  1. Select Start, then Settings, then System, then Troubleshoot, then Other troubleshooters.
  2. Find Hardware and Devices and select Run.
  3. Select Next and follow the prompts.

If that entry is missing, Dell suggests pressing Windows + X, opening Terminal (Admin) and running msdt.exe -id DeviceDiagnostic.

Stop Windows from powering down the USB root hubs

  1. Right-click Start and select Device Manager.
  2. Expand Universal Serial Bus controllers.
  3. Right-click a USB Root Hub and select Properties.
  4. Open the Power Management tab.
  5. Clear Allow the computer to turn off this device to save power.
  6. Repeat for every USB Root Hub, then restart.

Dell also lists turning off USB selective suspend under Edit Power Plan, Change advanced power settings, USB settings.

Microsoft strongly recommends leaving selective suspend on, so switch it back if it makes no difference.

Reinstall the USB controllers

  1. Unplug the USB device.
  2. Open Device Manager and expand Universal Serial Bus controllers.
  3. Right-click each entry and select Uninstall device.
  4. Restart the PC and let Windows reinstall the drivers automatically.

Install Windows updates and drivers

  1. Select Start, then Settings, then Windows Update.
  2. Select Check for updates.
  3. Install what is offered and restart when asked.

On a Dell PC, the Update software option in SupportAssist scans for driver and BIOS updates.

Dell recommends its own tools or its Drivers and Downloads page over third-party driver updaters.

Check that USB is enabled in BIOS

On a Dell PC, restart and press F2 repeatedly when the logo appears to open BIOS.

Look for USB Configuration, usually under Integrated Devices, and make sure the external USB ports option is checked.

Dell also describes pressing F9 to load defaults, then saving and exiting, and notes that BIOS menus vary by model.

Refresh the USB controllers in Safe Mode

If the ports work in Safe Mode but not normally, Dell says an app or driver conflict is likely.

  1. Select Start, then Settings, then System, then Recovery.
  2. Next to Advanced startup, select Restart now.
  3. Choose Troubleshoot, Advanced options, Startup Settings, then Restart.
  4. Press 4 or F4 for Safe Mode.
  5. In Device Manager, uninstall every USB Root Hub and every USB Host Controller.
  6. Restart normally and test the device.

Roll back with System Restore

Use this only if the ports worked before a recent update or install.

Dell notes System Restore is off by default in Windows 11, so an older restore point may not exist.

  1. Press Windows + R, type rstrui.exe and press Enter.
  2. Select Next and pick a restore point from before the problem began.
  3. Select Next, then Finish, and let the PC restart.

Your personal files are not touched, but apps, drivers and updates installed after that point are removed.

Where each setting lives

SettingPath in Windows 11
Hardware and Devices troubleshooterStart, Settings, System, Troubleshoot, Other troubleshooters
Root hub power savingDevice Manager, USB Root Hub, Properties, Power Management
USB selective suspendEdit Power Plan, Change advanced power settings, USB settings
USB connection notificationsSearch for usb, open USB settings, Connection notifications
Safe ModeSettings, System, Recovery, Advanced startup

When to contact support

If the device works on another PC and every port on yours fails, the hardware may need repair.

On a Dell PC, SupportAssist can test the ports under Support, I want to troubleshoot my PC, I want to check a specific piece of hardware, USB Ports.

Dell treats resetting the PC as a last resort after diagnostics pass, and warns to back up your data first.

Related fixes on this site: a USB drive not showing up, USB-C errors, a keyboard that is not working and a mouse that is not working.

Sources: Dell advanced USB troubleshooting, Dell USB ports not working and Microsoft Fix USB-C problems in Windows.

Leave a Reply

Your email address will not be published. Required fields are marked *