How To Fix Pixel Watch Not Pairing Or Connecting To Phone (2026)
A Google Pixel Watch that will not pair, or keeps showing as disconnected, usually needs a basic setting fixed on the phone or a restart of the watch.
Google’s help center sets out the requirements, a restart step, and a clear order of resets for the stubborn cases.
The steps below follow that order, so stop as soon as the watch connects.
Quick answer: start here
| Symptom | First thing to try |
|---|---|
| Pairing codes do not match | Restart the watch, then retry with the devices close together |
| Watch freezes while pairing | Hold the crown for 3 seconds and tap Restart |
| Disconnected shown on the watch | Check Bluetooth, Airplane mode and the app’s Nearby permission |
| Can’t pair or Can’t find your watch | Restart, then factory reset the watch |
| Can’t connect after a phone reset | Back up, factory reset the watch, then pair again |
Check the basics before pairing
Google’s setup guide says the Pixel Watch works with most Android phones running Android 10.0 or newer.
Charge both devices first, because a low battery can interrupt setup.
- Turn on Bluetooth on the phone.
- Allow location permissions and turn on Wi-Fi or a mobile connection.
- Update the watch firmware, the Pixel Watch app and the phone software.
- Install the Google Pixel Watch app from the Play Store.
Google says the Pixel Watch and Pixel Watch 2 only connect to Android phones.
Keep the phone close for Fast Pair
Fast Pair needs the phone within about 0.5 m or 1.6 ft of the watch.
If your phone does not show the prompt, open the Pixel Watch app and start pairing from there.
If the pairing codes do not match
Google says to press and hold the crown for 3 seconds, tap Restart, and wait until the watch is fully on.
Then bring the phone and watch together and compare the codes again before tapping Pair on the phone.
When pairing succeeds, the app shows Connected.
Fix a watch that shows disconnected
Google lists four requirements for a working Bluetooth link.
- Turn on Bluetooth on the phone.
- Turn off Airplane mode on both the phone and the watch.
- Make sure the phone is connected to the internet.
- Set the Pixel Watch app’s Nearby permission to Allow.
On the watch, Bluetooth is under Settings, then Connectivity, then Bluetooth.
Our guide to Pixel Wi-Fi and Bluetooth problems covers the phone side in more detail.
Fix a Network error on the watch
A Network error can mean the phone is not on Wi-Fi, because the watch joins Wi-Fi networks saved on the phone.
Connect the phone first, then check Settings, Connectivity, Wi-Fi on the watch.
Google says the watch cannot join networks that need a web page login first, such as hotel Wi-Fi, or 5GHz networks.
LTE watches: signal and eSIM
An LTE watch away from the phone relies on a carrier network, so signal strength matters.
Check it under Settings, Connectivity, Mobile, SIM status.
If you deleted the eSIM profile by mistake, go to Settings, Connectivity, Mobile, Advanced and follow the steps to add it again, and note that some carriers require a call to reactivate it.
See also our list of smartwatches with cellular support.
The reset order Google recommends
Google states that a factory reset erases all apps, settings and data on the watch, so try a restart first.
| Step | What to do |
|---|---|
| 1. Reset from the watch | Settings, then Disconnect & reset, then Ok |
| 1. Or reset from the app | In the Pixel Watch app, tap System, then Reset and unpair watch |
| 2. Clean up the phone | Uninstall the app, forget watches under Connected devices, restart the phone |
| 3. Fastboot reset | Hold the crown and side button for about 20 seconds |
| 4. Hard reset | Do it while the watch is on the charger |
Google lists Can’t pair, Can’t find your watch, Something went wrong, a forgotten PIN and a frozen G logo as reasons to reset.
If the watch will not reset
Uninstall the Pixel Watch app, open the phone’s Settings, tap Connected devices, and forget any watch listed.
Restart the phone, then keep the watch close, and the pairing screen should appear.
Fastboot reset steps
Use this only when the other resets fail, because it also wipes the watch.
- Hold the crown and side button for about 20 seconds until the G logo appears.
- Tap the upper-left and lower-right edges of the screen at the same time to enter Fastboot mode.
- Press the side button to scroll, highlight Recovery Mode and press the crown.
- When No Command appears, hold the crown and swipe up to open the debug screen.
- Swipe down to Wipe Data or Factory Reset and swipe right to confirm.
- Swipe right or press the crown on Reboot system now.
Settings paths on the watch
| Task | Path |
|---|---|
| Restart | Hold the crown 3 seconds, scroll, tap Restart |
| Bluetooth | Settings, Connectivity, Bluetooth |
| Wi-Fi | Settings, Connectivity, Wi-Fi |
| SIM status (LTE) | Settings, Connectivity, Mobile, SIM status |
| Factory reset | Settings, Disconnect & reset, Ok |
The Can’t connect error after a phone change
Google says this error can appear if you pair the watch with the same phone after that phone was factory reset.
It can also appear when you pair with a previously paired phone without pairing to a different phone first.
The fix is to back up the watch, factory reset it, and pair it again, with an optional restore from the backup.
Re-pairing after a reset
Sign in with your most recent PIN or Google Account when you pair again.
A Google Workspace account needs Device Management turned off, according to Google’s setup page.
If the watch will not charge before you can reset it, see our Pixel Watch charging guide, and for another brand see our Fitbit Charge 6 Bluetooth guide.
When to contact Google support
Google says if the watch still will not reset, contact Google support.
Google also notes that if setup takes more than 20 minutes, it has a separate setup troubleshooting article.
Sources: Fix Pixel Watch setup and phone pairing issues, Fix Bluetooth, connection and LTE issues, How to set up your Google Pixel Watch and Upgrade your watch or phone without losing data.