How To Fix A Dell Laptop No Boot Device Found Error (2026)
A Dell laptop that says “No boot device found” or “No bootable devices” cannot find a drive to start Windows from.
Dell publishes a fixed order of checks for it, and the early ones cost nothing.
Work through them in order and stop as soon as Windows loads.
Quick answer: what to try first
| Step | What to do | Why |
|---|---|---|
| 1 | Unplug every USB drive, card and dock, then restart | A device ahead of the internal drive in the boot order can trigger the message |
| 2 | Hard reset: hold the power button 10 seconds, unplug power, hold it 15 to 20 seconds | Clears leftover charge |
| 3 | Press F2 and check the drive is listed and the boot mode is UEFI | A missing drive or wrong mode causes this error |
| 4 | Press F12 and run Diagnostics | Tests the drive without Windows |
| 5 | Repair or reinstall Windows | Only if the drive passes |
What the message means
Dell’s support pages treat the message as a sign that the BIOS cannot find anything it can start Windows from.
That can mean the drive is not detected, the boot order is wrong, the boot mode does not match the installed system, or the startup files are damaged.
| Cause | Where it is fixed |
|---|---|
| Loose connection or a shifted M.2 SSD | Reseat the drive |
| Another device ahead of the internal drive | Boot Sequence in the BIOS |
| Boot mode set to Legacy, or Windows installed in a different mode | Boot Sequence, then possibly a reinstall |
| SATA mode changed from RAID On to AHCI | SATA Operation in the BIOS |
| Damaged boot files | Windows Recovery Environment commands |
| Drive failure | Replace the drive, usually under warranty |
If your screen says “Hard drive not installed” instead, the cause list is shorter and a separate fix applies.
Disconnect everything and do a hard reset
Dell starts with the simplest step, which is removing every external device except the keyboard and mouse.
- Hold the power button for 10 seconds to turn the laptop off.
- Unplug USB drives, SD cards, printers, webcams and docking stations.
- Restart the laptop and see whether the message returns.
If it starts, plug the devices back in one at a time to find the one that was taking priority.
If the message stays, do the hard reset below.
- Turn the laptop off and unplug the power cable.
- Remove the battery if your model has a removable one.
- Press and hold the power button for 15 to 20 seconds.
- Reconnect power and press the power button.
Check the drive and boot order in the BIOS
Restart and tap F2 at the Dell logo to open the BIOS or UEFI setup.
- Open General > System Information (or the Storage section on newer systems) and look for your drive.
- If it is not listed, the laptop cannot see it at all, so go to the reseat section below.
- Open General > Boot Sequence (or Boot Configuration > Boot Sequence) and move the internal drive or Windows Boot Manager to the top.
- Save the changes and restart.
Menu names vary by model, so Dell tells owners to use the manual for their Service Tag.
Switch the boot mode from Legacy to UEFI
One Dell article is written specifically for this message after the boot sequence was set to Legacy.
It covers computers with 7th-generation Coffee Lake or newer processors, which Dell says are designed to start only in UEFI mode.
On those computers Dell supports Windows 10 and later, and Linux, in UEFI mode only.
| If this is what happened | What Dell says to do |
|---|---|
| Windows was installed in UEFI, then the boot sequence was changed | Change the boot sequence back to UEFI to recover |
| Windows was installed in Legacy mode | Switching back to UEFI does not recover it, so reinstall the operating system |
To switch back, press F2, choose Boot sequence, change Legacy to UEFI and click Apply.
Then open Advanced Boot Options and turn off Enable Legacy Option ROMs.
Finally click Exit and let the laptop restart.
Check the SATA operation setting
A SATA mode that no longer matches what Windows was installed with can also stop the drive from being usable.
- In the BIOS open System Configuration > SATA Operation.
- If it says RAID On and you do not use RAID, Dell says to change it to AHCI when the drive is not detected.
- Save and restart.
Dell warns that changing this on a working Windows installation can cause an Inaccessible Boot Device blue screen.
Only change it when the drive is not detected or you are doing a clean install.
Run the Dell hardware diagnostic
The diagnostic checks the drive without loading Windows, so it works even when the laptop cannot start.
- Turn the laptop on and press F12 repeatedly until the One Time Boot Menu appears.
- Select Diagnostics and press Enter.
- Let the quick test finish.
If it passes, Dell says the drive hardware is fine and the cause is likely a BIOS setting or damaged Windows files.
If it fails, write down the error code, the validation code and the Service Tag, then look the code up on Dell’s pre-boot analysis page.
Drive codes such as 2000-0141 and 2000-0150 mean no drive was detected, and Dell’s advice for them is to reseat the drive and cables.
Reseat the drive if it is not detected
If the BIOS does not list the drive, a loose connection is the first thing Dell suggests checking.
- Shut the laptop down, unplug power and touch bare metal to ground yourself.
- Open the bottom panel using the service manual for your model.
- Disconnect the drive, or for an M.2 SSD remove its screw and slide it out.
- Check the connector and slot for dust.
- Reinsert it firmly, tightening the screw on an M.2 drive.
- Close the panel and rerun the diagnostic.
Repair Windows when the drive is detected
When the drive passes the test and appears in the BIOS, the startup files are the likely problem.
Dell’s boot guide opens the Windows Recovery Environment through the SupportAssist OS Recovery option.
- Turn the laptop off, press the power button and tap F12 about once a second.
- Select SupportAssist OS Recovery.
- Click the three dots at the upper right and choose Windows recovery.
From there Dell lists these options.
| Problem | Option in Windows recovery |
|---|---|
| A recent update caused it | Troubleshoot > Advanced Options > System Restore |
| Cause unknown | Troubleshoot > Reset this PC > Keep my files |
| Boot configuration missing or damaged | Troubleshoot > Advanced Options > Command Prompt |
| Nothing else works | Fresh installation |
In the Command Prompt Dell runs bootrec /fixmbr, bootrec /fixboot, bootrec /scanos and bootrec /rebuildbcd in that order, and says bootrec /fixboot may return an access denied message, in which case you continue with the next command.
If BitLocker asks for a key, see our guide to finding your BitLocker recovery key.
Rebuild the UEFI boot files
For UEFI systems Dell adds a second method in the same Command Prompt.
- Run
diskpart, thenselect disk 0andlist partitionand note the EFI partition number. - Run
select partitionwith that number, thenassign letter=Sandexit. - Run
bcdboot C:\Windows /s S: /f UEFI. - Run
diskpartagain, select the same partition, runremove letter=Sandexit.
Restart afterwards and check whether Windows loads.
When to contact Dell support
Contact Dell if the drive is missing from the BIOS after reseating, if the diagnostic fails again, or if the laptop makes clicking or grinding sounds, which Dell says points to a failing hard disk.
Have your Service Tag and any error codes ready.
Related guides on this site cover a Dell laptop stuck on the logo, checking and repairing drive errors in Windows 11 and setting up a new drive.
Sources: Dell KB 000128655, Dell hard drive and SSD issues and Dell KB 000124359.