|

How To Fix A Dell Laptop Fingerprint Reader Not Working (2026)

A Dell fingerprint reader that stops recognizing your finger is usually a driver, BIOS or Windows Hello problem rather than a dead sensor.

Dell publishes one ordered troubleshooting list for it, and this guide follows that order.

Work through the steps in sequence and test a fingerprint sign-in after each one.

Quick answer: what to try first

What you seeTry this first
Fingerprint option missing on the lock screenSet it up again under Sign-in options, then check for Windows updates
Set up button missing or greyed outCheck Device Manager for a Biometric devices entry
Reader worked before, now failsRestart, then do a hard reset
Started after reinstalling WindowsInstall the latest BIOS and drivers
Scans fail only sometimesClean the sensor and re-enroll the finger

Dell lists scratches, grease or dust on the sensor, corrupted drivers, outdated chipset firmware, wrong Windows Hello settings and corrupted system files as the usual causes.

Confirm your Dell has a fingerprint reader

Not every Dell has one, and Dell says the quickest check is the Windows Hello fingerprint option in Settings.

If that option never appears under Sign-in options, the computer has no reader.

You can also check the invoice or the manual for your model on Dell’s manuals page.

Where the reader is on a Dell

The location depends on the model, and Dell gives these examples.

ModelReader location
Vostro 5502Power button
Latitude 5410Power button
Latitude E5470Palm rest
Latitude 12 7202Back panel
Dell MS819 mouseOn the mouse

Wipe the sensor with a clean dry cloth, because grease and dust are on Dell’s cause list.

Restart the computer first

Save your work, close your browser pages and restart the computer.

Then try signing in with your fingerprint again.

If it still fails, move on to the hard reset.

Do a hard reset

A hard reset drains leftover power and clears stuck hardware states.

  1. Turn off the computer, then hold the power button for 10 seconds.
  2. Unplug the AC adapter or power cable, and remove the battery if it is removable.
  3. Disconnect extra devices such as USB drives, printers, webcams and memory cards, keeping only the keyboard and mouse.
  4. Hold the power button for 15 to 20 seconds.
  5. Reconnect the power cable, AC adapter and battery.
  6. Turn the computer on and test the fingerprint reader.

On laptops with a battery you cannot remove, Dell points to its separate real-time clock reset article instead of step 2.

Update the BIOS and drivers

Dell says outdated chipset firmware is a known cause, especially after Windows was reinstalled.

  1. Open SupportAssist from the Start menu.
  2. On the Home tab, select Update Software.
  3. Click Start to check for driver and BIOS updates.
  4. Follow the prompts and restart if asked.

Fingerprint drivers sit in the Security category, and the vendor name can be Synaptics, Dell ControlVault, Validity or Goodix.

If the reader is a non-Dell device, such as a third-party mouse or scanner, get its driver from that maker’s website.

Set up Windows Hello again

Wrong Windows Hello settings are on Dell’s cause list, so redo the setup.

  1. Search for and open Sign-in options.
  2. Under Windows Hello Fingerprint, click Set up.
  3. Follow the on-screen instructions.
  4. Press Windows logo + L to lock the PC and confirm the fingerprint option shows on the lock screen.

If the option is missing, run Check for updates, install what Windows offers, and repeat the steps.

Check Device Manager when Set up is missing

If there is no Set up button, check whether Windows can see the reader at all.

  1. Open Device Manager.
  2. Expand Biometric devices and confirm the reader is listed.
  3. If it is not there, expand Unknown devices.

A reader that is missing from Device Manager means the driver or hardware needs attention, so go back to the driver step above.

The order Dell recommends

Dell’s list runs from the quickest checks to the steps that change your system.

StepWhat it rules outRisk to your files
RestartA temporary software glitchNone
Hard resetStuck hardware state or residual powerNone
BIOS and driver updateCorrupted drivers and old chipset firmwareNone
Hardware and Devices troubleshooterCommon device configuration faultsNone
Dell diagnostic testA failed sensorNone
Windows updatesMissing Windows Hello fixesNone
System RestoreA recent software changeApps installed after the restore point are removed
New user accountA damaged profileNone
Reset WindowsCorrupted system filesDeletes all data

Stop at the first step that restores the fingerprint sign-in, because the later steps are heavier.

Run the Hardware and Devices troubleshooter

Dell gives this Windows 10 and 11 troubleshooter as the next step.

  1. Press Windows logo + R.
  2. Type msdt.exe -id DeviceDiagnostic and press Enter.
  3. Click Next in the Hardware and Devices window.
  4. Apply any fix it recommends and restart.

Run Dell’s fingerprint reader diagnostic

Dell has a hardware test page for the reader that uses SupportAssist and installs it if needed.

If the test passes, restart and try signing in again.

If the test fails, Dell says to contact Dell Technical Support for repair options in your region.

Install Windows updates and try System Restore

Search for Check for updates, click Check for updates or Download now under Windows Update, then restart.

If the reader broke after a recent change, Dell suggests System Restore before any factory reset.

System Restore needs a restore point from before the problem began.

Try a new user account

A new account shows whether your profile is the problem.

  1. Search for and open Other Users.
  2. Click Add account.
  3. Choose I don’t have this person’s sign-in information and follow the prompts.
  4. Set up Windows Hello fingerprint sign-in on the new account and test it.

If it works there, you can switch to the new account and copy your personal files across.

Last resort: reset Windows

Dell lists resetting or reinstalling Windows as the final step.

This permanently deletes all user data, so back everything up first.

Our guide to Dell SupportAssist OS Recovery not starting helps if the recovery tool itself fails.

How to remove a saved fingerprint

Removing the old print and enrolling it again can fix scans that fail only sometimes.

  1. Press Windows key + Q and open Settings.
  2. Select Accounts, then Sign-in options.
  3. Choose Fingerprint recognition (Windows Hello).
  4. Click Remove, then set it up again as above.

When to contact Dell

Contact Dell Technical Support if the diagnostic test fails or the reader never appears in Device Manager.

Related guides on this site cover a Dell laptop that will not turn on and a Dell ePSA error code.

Official sources: Dell fingerprint reader troubleshooting and Dell fingerprint enrollment guide.

Leave a Reply

Your email address will not be published. Required fields are marked *