Roborock Error Codes And How To Fix Them (2026)

A Roborock that stops and reads out an error number is telling you which part to check.

Roborock’s own support pages list the common codes, and most are fixed by cleaning a sensor or freeing a brush or wheel.

The tables below turn those pages into a checklist, with a warning about where code meanings differ between models.

Quick answer: the most common codes

CodeUsual areaFirst thing to try
1Laser unitCheck that the laser can spin, and clear anything blocking it.
4Cliff sensorWipe the cliff sensors and keep the robot off dark carpet.
5Main brushClear tangles from the brush and its housing.
7WheelsSpin the wheels by hand and free anything stuck.
13ChargingClean the charging contacts on the robot and dock.
18FanClap the side of the robot to dislodge debris.

Code meanings differ by model

Roborock publishes separate charts for different models, and a few numbers do not mean the same thing across them.

Code 9 is a filter message on the S4 page, but a missing dustbin on the Q7 Max manual’s chart.

Code 18 is a debris-in-the-fan issue on the S4 page and a general fan fault on the Q7 Max chart.

Check the code against your own model’s manual in the Roborock app or on support.roborock.com when the table below does not fit.

How an error is announced

The Q7 Max manual says the power indicator flashes red quickly and a voice alert sounds when an error happens during cleaning.

Most errors clear after you fix the cause, move the robot and start cleaning again.

After any sensor error, clean that sensor before retrying.

The Q7 Max manual adds that a malfunctioning robot left alone for over 10 minutes goes to sleep.

Placing it on the dock by hand ends the current cleanup.

Sensor and laser errors

CodeMeaningFix
1Laser unit not spinning or blockedPower on, check the laser spins, and rotate it gently by hand if it does not, then restart.
4Cliff sensorWipe the cliff sensors; see whether it only happens on carpet.
164ToF cliff sensor (newer models)Reset the robot using the reset button in the user manual’s diagram.

Dark or shag carpet can look like a drop to cliff sensors, which is why Roborock suggests testing whether the error is carpet-only.

Wheel and movement errors

Codes 3 and 7 point to the wheels, and the Saros 20 Flow page gives the same checks for both.

Look for foreign objects stuck in the main wheels, and note whether it only happens on carpet.

Push the robot firmly forward and backward for about 10 seconds, and inspect the main brush, brush cover, water tank and mop mount for blockage.

Code 8 means the robot is blocked or has lost its position, depending on the model.

Roborock says not to move the robot while it cleans, and to clear obstacles and remove the water tank if one is fitted.

If code 8 keeps happening, delete the map and remap the home, and send support a photo if it always happens at one spot.

Brush errors

CodeMeaningFix
5Main brush tangled or stuckClear the brush slots and both brush ends; run with Carpet mode on, and update the firmware.
6Side brushRemove it, clear hair from the mount and gear area, reinstall firmly, then reboot with the power button.

Filter, dustbin and fan errors

For a filter or fan code, empty the dustbin and clean the filter first.

Roborock says to dry a washed filter fully, for at least 12 hours outdoors in the sunlight on the Saros page, and up to 24 hours on the Q7 Max chart.

Codes 10 and 18 share the same fixes on the Saros page, including a reboot, balanced or normal cleaning mode, and a firmware update.

On the S4 page, code 9 asks you to look for a magnet on the filter’s side, and to replace the filter if there is none.

Charging and dock errors

Code 13 is a poor charging contact on the S4 page, where the dock light stays on.

Adjust the robot on the dock until the light goes off, then clean the contacts on both the robot and dock.

Check the dock’s power cable and try another outlet.

For a robot that cannot find its dock, place the dock against a wall with 0.5 m clear on each side and 1.5 m in front.

Clean the dock’s front signal area and the robot’s front sensor as well.

Battery and other codes on the Q7 Max chart

CodeMeaningFix
12Low batteryRecharge, then retry.
14Battery faultNo fix is listed.
16Robot tiltedMove it to level ground and restart.
22Dock locator faultClean the dock locator, then retry.
23Cannot return to dockClean the dock location beacon, then retry.

If the battery is at an abnormal temperature, wait for it to return to normal before using the robot.

Zone cleaning that will not start

The S4 page says to start a normal cleaning near the open door first, then try the zone cleaning again.

If a no-go zone or invisible wall is detected, move the robot out of that area, since the Q7 Max chart treats it as a message instead of a fault.

Internal errors and resets

For an internal error, open the top cover and press the Reset button, whose position varies by model.

Roborock warns that this restores factory settings, including Wi-Fi and cleaning schedules.

Codes 109 and 155 on the Saros 20 Flow page use this same reset.

Wheel codes 105, 106, 107, 108 and 116 are handled by pushing the robot back and forth for about 10 seconds.

Do not push for too long, because the motor can overheat.

When to contact Roborock

If an error persists after these steps, the S4 page says to contact Roborock Customer Support.

The Saros 20 Flow page lists [email protected], which it says replies within 1 business day.

It also lists a US phone line, 1-855-960-4321, available 24/7.

For other smart home devices that go offline, see our fix for a Honeywell Home thermostat that is offline or how to factory reset a Nest speaker or display.

Sources: Roborock S4 error messages, Roborock Saros 20 Flow error codes, Roborock Q7 Max manual.

Leave a Reply

Your email address will not be published. Required fields are marked *