|

GE Universal Remote Codes: How To Program It (2026)

A GE universal remote needs a four-digit code for your TV before it can control it, and you can set it up with a code or without one.

The steps below come from Jasco, the company that makes GE universal remotes, and they use the manual for the GE 4-Device Universal Remote (Jasco 34932 and 25006).

Other GE and UltraPro models can differ a little, so check the manual for your own remote if a step does not match.

Quick answer: two ways to program it

MethodUse it whenJasco says
Direct code entryYour brand is in the code listRecommended method
Auto code searchYour brand is not listed, or the listed codes do not workOnly some remotes have it, and it needs a device that has power on and off

Before you start

  • Put two AAA batteries in the remote, because they are not included.
  • Turn on the device you want to program.
  • Point the remote at the device with nothing in the way.

The 4-Device remote comes preset for Samsung TVs, so pressing TV controls a Samsung TV without programming.

You can also program a cable box, DVD player or other device on the CBL, DVD and AUX buttons, and any of those buttons can control any type of device.

Find the code list for your remote

Jasco keeps an online code list, and your remote may also come with a printed one.

If you do not have the list, open the battery compartment and look for a sticker under the batteries or on the underside of the cover.

The sticker shows the list version, which is CL3, CL4, CL5 or CL6.

Put the batteries and cover back, then look up your list version, the device type and your brand.

Each brand has one or more four-digit codes, and you try them in order until one works.

Program it with a code (direct code entry)

  1. In the code list, find your device type and brand, and circle every four-digit code for that brand.
  2. Press and hold SETUP until the red light comes on, then let go. The light stays on.
  3. Press and release the device button you want to program (TV, CBL, DVD or AUX). The light blinks once and stays on.
  4. Type the first four-digit code with the number buttons. The light turns off after the fourth digit.
  5. Point the remote at the device and test the buttons.
  6. If the device does not respond properly, repeat from the second step with the next circled code.

Some codes control only a few functions, so test the other circled codes for more.

For a combo device such as a TV with a built-in DVD player, you may need a separate code and a separate device button for each part.

Write down the codes that work.

Program it without a code (auto code search)

Use this when your brand is not in the list, and note that it will not work on a device that cannot be turned on and off.

  1. Turn the device on by hand.
  2. Press and hold SETUP until the red light comes on, then let go.
  3. Press and release the device button (TV, CBL, DVD or AUX). The light blinks once and stays on.
  4. Point the remote at the device and press and release POWER. The remote sends 10 codes, blinking once for each, and then stays on.
  5. If the device did not turn off, press POWER again to send the next 10 codes.
  6. When the device turns off, turn it back on by hand.
  7. Point the remote at it and press and release VOL, which resends the first code in that batch.
  8. Keep pressing VOL about 3 seconds apart until the device turns off, then press the same device button from step 3 to store the code.

VOL can also step backward through the batches, and the light flashes twice at the first or last code in a batch.

Turn the device on with the remote and test the buttons, and if the code is not good enough, start the search again.

Check which code is stored

  1. Press and hold SETUP until the red light comes on, then let go.
  2. Press the device button whose code you want.
  3. Press ENTER.
  4. Press 1 and count the light flashes, which is the first digit. Repeat with 2, 3 and 4 for the other digits.
  5. Press ENTER to exit.

Make the volume buttons control one device

Master Volume lets the volume buttons control one device, such as a soundbar, whichever device button you picked.

  1. Press and hold SETUP until the red light comes on, then let go.
  2. Press the device button for the device that should control volume.
  3. Press MUTE.
  4. Press VOL. The light blinks twice and turns off.

To turn it off, repeat the same steps using the same device button.

Use Shift mode for Menu, Guide, Mute and Exit

Press SETUP/SHIFT once, then press the key that has the shift function, and Shift mode ends after 10 seconds or when you press SETUP/SHIFT again.

To getPress
GuideSETUP/SHIFT, then INPUT
MenuSETUP/SHIFT, then INFO
MuteSETUP/SHIFT, then OK
ExitSETUP/SHIFT, then PREVIOUS CHANNEL

If the remote still does not work

ProblemWhat Jasco says to try
Remote does not control the deviceReplace the batteries and confirm the correct polarity, aim straight at the device, choose the right device button, and try a different code
Only some buttons workTry other codes from the list, or run the auto code search
A button does nothingThe original remote may not have that feature
Volume works but channels do notProgram the remote to your cable, satellite or converter box
Menu or arrow keys do not workUse Shift mode, or program a different device code
Roku Streaming Stick or Amazon Fire TV does not respondThey use RF and not infrared, so the remote cannot control them

Jasco adds that bad batteries are the most common cause of strange red light behavior, so try a different set.

Changing batteries without losing codes

You do not need to program the remote again after a battery change, because the code saver keeps the codes for up to 10 minutes.

Swap the batteries within that time.

Reset the remote to factory settings

  1. Press and hold SETUP until the red light comes on, then let go.
  2. Press MUTE.
  3. Press 0. The light flashes twice, and all programmed codes are erased.

Jasco customer service is at (800) 654-8483, Monday through Friday, 7am to 6pm CDT.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *