How To Fix An Offline eero Network (2026)

When your whole eero network goes offline, the cause is almost always between the modem and the gateway eero.

The eero app can tell you which link in that chain failed.

These steps come from eero’s support articles on offline networks, the “Cannot connect to the internet” message, and offline devices.

Quick answer: match the app message to the fix

What the app reportsWhere the problem isFix
Phone not connectedYour phone is not on the eero Wi-FiReconnect to the eero network in Wi-Fi settings
WAN not detectedThe cable or modemUnplug extra modem cables, power cycle the modem
ISP settings failLogin or VLAN detailsEnter the ISP settings your provider documents
WAN IP not identifiedISP outage or modemCheck the ISP site, then power cycle
Default router unreachableOutage or third-party gearCheck the ISP site and DHCP/DNS settings
DNS resolution errorOutage or blocked DNSCheck the ISP site and any security equipment

Check your network status in the app

Open the eero app and tap Home in the bottom-left corner.

A down network shows Offline in red with a Troubleshoot your connection prompt.

Tap the arrow beside it to let the app diagnose the problem.

Connect your phone to the eero network

The troubleshooting details work even while the network is offline, as long as your phone is on the eero Wi-Fi.

If it will not rejoin, turn your phone’s Wi-Fi off and back on so it reconnects.

Keep working with Hotspot Backup

Hotspot Backup lets your eeros use a mobile hotspot or another Wi-Fi network while you fix the main connection.

  1. Make sure a mobile hotspot or backup Wi-Fi network is active.
  2. On the Home tab, tap Internet.
  3. Tap the arrow beside the Hotspot Backup options.
  4. Follow the in-app directions to connect your eeros.

What the app actually checks

After a check, the app confirms you are back online only when the phone connection and the WAN connection both pass.

The WAN check covers an Ethernet connection, compatible ISP settings, an assigned WAN IP address, a default router IP, and successful DNS resolution.

A failure at any one of those points counts as a failed WAN connection.

If your phone is connected but the WAN is not detected

  1. Unplug every Ethernet cable from the modem except the one going to the gateway eero.
  2. If there is still no internet, unplug the modem or ONT for at least 3 minutes.
  3. Make sure the cable to the gateway sits firmly in the correct port, often labeled LAN or Ethernet.
  4. Plug the modem back in and allow 5 to 10 minutes for it to reconnect.
  5. Restart the gateway and wait for a solid white LED.
  6. If it still fails, try a different Ethernet cable and repeat.

If the app says Cannot connect to the internet

Eero says this usually means the modem is offline, your ISP has an outage, or your ISP requires login details.

If your provider gave you a username, password, or special settings, tap Internet settings in the app and enter them first.

  1. Unplug all Ethernet cables from the modem.
  2. Connect the eero to the port labeled WAN or Internet on the modem, using the cable that came with the eero.
  3. Unplug the modem for 30 seconds, then plug it back in, and wait 3 to 5 minutes for the lights to settle.
  4. If you already restarted the modem, leave it unplugged for 2 to 3 minutes this time.

Power-cycle timings in eero’s articles

SituationUnplugged forThen wait
Modem or ONT, WAN not detectedAt least 3 minutes5 to 10 minutes, then restart the gateway until solid white
Modem, Cannot connect to the internet30 seconds (2 to 3 minutes on a repeat)3 to 5 minutes for steady lights
Gateway eero, several devices offline30 secondsAbout 2 minutes for solid white

If ISP settings, WAN IP, router IP, or DNS fail

For an ISP settings failure, confirm the cable is fully seated, power cycle the modem or ONT, and then enter any VLAN, static IP, or PPPoE details exactly as your ISP documents them.

For a missing WAN IP, check your ISP’s website for an outage and use Hotspot Backup until it ends.

For an unreachable default router, eero adds that third-party equipment must allow DHCP and DNS traffic to reach the gateway.

For a DNS error, check for an outage and confirm any third-party security equipment allows DNS traffic.

How to edit ISP settings in the app

Most connections use DHCP, but some providers need a specific setup such as an uplink VLAN.

  1. Tap Settings in the bottom-right corner.
  2. Tap ISP Settings.
  3. Choose DHCP, Static IP, PPPoE, or Uplink VLAN, as your ISP requires.
OptionWhat to enter
DHCP or Static IPIP address, subnet mask, and router IP, then Save settings
PPPoEUsername and password, then Save settings
VLANTurn on Uplink VLAN Tag, enter the VLAN ID, then Save settings

If the app cannot reach the default DHCP settings, it tells you to contact your ISP.

If only some devices show offline

Eero’s offline-device article lists several causes, starting with a nearby network that shares your eero network’s name.

  • Restart the device fully, wait 30 seconds, and turn it back on.
  • In the app, tap Home, then Devices, and check whether the device is paused or blocked.
  • Check the device’s Profile and Unassigned Device Control for restrictions.
  • Move the device or an eero closer, since one bar or less is poor and three or more is the goal.
  • Forget the eero network on the device and rejoin it.
  • Turn off the private or randomized MAC address for the eero network.

If several devices are offline, power cycle the gateway, wait 30 seconds, and allow about 2 minutes for a solid white LED.

For a red light on an individual eero, read how to fix a red light on your eero.

If you run Starlink, see using mesh routers with a Starlink setup.

Another brand’s version of this problem is covered in fixing a Netgear router with no internet.

When to contact eero support

If you still cannot get a WAN connection after these steps, eero tells you to contact its support team.

Phone numbers, international support, and ticket submission are listed at eero.com/support/contact-us.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *