How To Fix An ASUS Laptop That Won’t Turn On (2026)
An ASUS laptop that will not turn on is usually a power-supply problem, a stalled reset or a BIOS process that is still running.
ASUS separates the case with no lights at all from the case where a light is on but the screen stays black.
This guide follows ASUS support steps in that order, starting with the checks that take a minute.
Quick answer: match what the laptop does
| What you see | What ASUS says to try |
|---|---|
| No lights and no sound | Check the adapter, cord and outlet, remove external devices, then do an EC and RTC reset. |
| Power light on, black screen | Remove external devices, try an external monitor, press Windows key + Ctrl + Shift + B, then reset. |
| Power or battery light flashing | Leave it on power and wait. A BIOS recovery is running. |
| Black screen after changing RAM or the battery | Wait for memory training to finish. |
| White text on black | Read the message. F1 opens BIOS setup, and S.M.A.R.T. Status Bad points to the drive. |
| Windows welcome screen, then black | Boot into Safe Mode and reinstall the graphics driver. |
Check the adapter, cord and outlet
ASUS begins with the power source because a bad adapter looks exactly like a dead laptop.
- Confirm the power cord, adapter, extension cord and wall outlet are all secure, and that any extension cord switch is on.
- Use the original adapter and cord for your model, because power output can differ between ASUS products.
- Check the power connector on the laptop for looseness, and try another outlet or cord.
- Inspect the adapter and cable for damage, and replace damaged parts through an authorized service center.
- Reseat the cable at the wall, the adapter and the laptop.
If the battery is removable, ASUS says to take it out and put it back in, and to skip this on models where it is not removable.
If the laptop has sat unused for a long time, connect power and leave it charging overnight.
For a USB Type-C charger, confirm that the port supports battery charging, which your user manual lists.
Remove everything plugged in
External hardware can stop a laptop from starting, so ASUS asks you to strip it down to the bare machine.
- Unplug the keyboard, mouse, external drives, printers and memory cards.
- Remove any disc and any card reader adapter.
- Disconnect every external monitor.
- If you recently added a hard drive or memory, remove it or restore the original configuration.
Then reconnect only the power adapter and press the power button.
Do an EC and RTC reset
The embedded controller is a motherboard chip that manages power and hardware, and ASUS says resetting it returns the hardware to its default state.
- Remove all external devices, including drives, printers, memory cards and dongles.
- Turn the laptop off, and save open files first if it still responds.
- Connect the power adapter.
- Press and hold the power button, using the hold time for your model.
- Turn the laptop on and check whether it starts.
| Model type | How long to hold the power button |
|---|---|
| 40-second models | Hold for 40 seconds, then release. |
| 20-second models | After 15 seconds the power light flashes quickly for about 3 to 5 seconds, so release when the flashing stops. |
ASUS does not say which models use which hold time, so check your user manual if the first attempt does nothing.
The same reset applies to notebooks, all-in-one PCs and gaming handhelds.
Power light on but nothing on screen
When the light is on and the display is black, ASUS gives a separate sequence for notebooks.
- Connect an external monitor and press Windows key + P to cycle display modes.
- If the external monitor works, install the display driver from the ASUS support site, and update both graphics adapters if the laptop has two.
- Press Windows key + Ctrl + Shift + B to reset the display.
- Remove external devices and any recently added drive or memory.
- Disconnect power, do the EC and RTC reset, reconnect power and press the power button.
If your laptop starts but the picture is the only problem, our Dell laptop black screen guide shows the same pattern on another brand.
If the power or battery light is flashing
A flashing light means the BIOS recovery process is running, and the screen stays black while it works.
| Step | Time ASUS gives |
|---|---|
| Wait for the BIOS ROM recovery window to appear | About 5 to 8 minutes |
| Recovery once the window is showing | Roughly 2.5 to 3.5 hours |
On a notebook, watch the battery charge indicator, and keep the laptop on power without forcing a shutdown.
Black screen after changing memory or the battery
After a BIOS update, a disconnected battery, new RAM or a reset, the laptop retrains its memory on the next start.
The screen can stay black with the power light on, or show Working on Memory Training.
- Keep the laptop plugged in and do not force a shutdown.
- ASUS support pages give different waits, from 1 to 3 minutes on one page to 5 to 10 minutes on another, with larger memory taking longer.
- Most systems show no text during training.
Wait the longer time before you decide it has failed.
If a BIOS update was interrupted
A forced shutdown during a BIOS update can leave the laptop unable to start.
ASUS describes three screens, and the first one needs no action.
- If an automatic recovery prompt appears, keep the laptop on power and wait 60 seconds, or choose Yes.
- If manual recovery is needed, download the BIOS file for your exact model on another computer and copy it to the root of a FAT32 USB drive.
- Hold the power button about 15 seconds until the light goes off, insert the drive, keep the adapter connected and power on.
If the ASUS Firmware Update (EZ Flash) screen appears instead, update from that screen.
On a black screen with the power light on and no text at all, ASUS says to do the EC and RTC reset on notebooks.
White text on a black screen
A message means the laptop is starting, so read it before you do anything else.
| Message | Meaning and action |
|---|---|
| S.M.A.R.T Status Bad | The drive is reporting a problem, and ASUS has a separate guide for it. |
| Press F1 to enter setup | The BIOS found a hardware configuration error, so press F1 and load the default settings. |
| Text about a failed BIOS update | Follow the interrupted BIOS update steps above. |
Goes black after the Windows welcome screen
If the laptop reaches the Windows welcome screen and then goes black, ASUS points to the graphics driver.
- Boot into Safe Mode.
- Reinstall the graphics driver from the ASUS support site.
When to contact ASUS
If the laptop starts but will not hold a charge, read our ASUS battery not charging guide.
If none of these steps work, ASUS tells you to contact customer support.
In North America that means ASUS Technical Support or the repair services on the ASUS USA support page.
ASUS notes that screens and steps can differ by model and software version, so check your user manual for model details.