How To Fix A Dell Monitor That Says No Signal (2026)

A Dell monitor that shows “No Signal” is powered on but is not getting a picture from the computer.

The cause is usually a cable, an input setting, or the wrong port on the PC, and rarely the monitor itself.

This guide follows Dell’s own support articles, so you can work through the checks in the order that rules out the cheap causes first.

Quick answer: what to check first

Start with the power light, because Dell uses it to tell you whether the problem is the monitor or the signal.

What you seeWhat it means (per Dell)Do this
Solid white or green lightPower and a video signal are presentLook at display settings, drivers and the resolution
Amber, orange or blinking white lightPower is present but there is no video signalCheck the cable, the input source and the PC port
No lightThe monitor is not getting powerFollow Dell’s “won’t turn on” steps instead

The indicator colors above come from Dell’s monitor troubleshooting article, and your model’s manual has the exact behavior.

Read the power light

An amber, orange or blinking white light means the monitor has power and is waiting for a picture.

That points you at the computer or the cable, so there is no reason to open the monitor’s menus yet.

If the light is completely off, the monitor has no power, and you should check the outlet and power cable before anything else.

Select the correct input source

Dell tells you to confirm that the monitor is set to the input you actually plugged into, such as HDMI or DisplayPort.

  1. Press a button on the monitor to open its on-screen menu.
  2. Open the input or source setting.
  3. Choose the port that your cable is plugged into.

On a laptop, press the Windows key and P together and choose Duplicate or Extend, because the laptop may be sending the picture only to its own screen.

Reseat or swap the video cable

Turn off the monitor and the computer, then make sure the monitor is on a working power outlet.

Check that the HDMI, DisplayPort or USB-C cable is firmly seated at both ends.

If you can, swap the power cable or the video cable to rule out a faulty connection.

Dell also recommends using the video cable that came with the monitor.

Use the right port on the PC

If your desktop has a separate graphics card, plug the monitor into the card and not into the motherboard.

The graphics card ports are usually lower on the back panel, while the ports built into the motherboard sit higher up.

Use the built-in ports only when the computer has no separate graphics card.

Your desktop hasPlug the monitor intoUsual location
A separate graphics cardThe graphics card portsLower on the back panel
No separate graphics cardThe built-in motherboard portsHigher on the back panel

Do a hard reset of the computer

Dell lists a hard reset as the first step when the screen stays blank at startup.

  1. Turn off the computer.
  2. Unplug the power cable from the computer.
  3. Disconnect peripherals such as external drives and printers, but leave the keyboard and mouse.
  4. Hold the power button for 15 to 20 seconds.
  5. Reconnect the power cable and turn the computer on.

If the picture returns, plug the other devices back in one at a time to find the one that caused the problem.

Run the monitor self-test

The self-test tells you whether the monitor is working on its own.

  1. Turn off the monitor.
  2. Unplug the video cable from the monitor.
  3. Turn the monitor back on.

If a self-test screen appears, Dell says the monitor is functioning correctly, and the fault is the computer, the cable or the port.

If colored lines show up during the self-test with every video cable unplugged, Dell says the panel has a hardware problem and the monitor needs warranty service.

Try the monitor on another computer

Connect the monitor to a different computer, or connect a different monitor to yours.

If the monitor works elsewhere, Dell says the likely culprit is the original computer’s graphics card.

Dell’s SupportAssist includes a video card test you can run on a Dell computer.

USB-C monitors with no picture

A USB-C port only carries video if it supports DisplayPort Alt Mode, and Thunderbolt ports do too.

Port or cableVideo over USB-C?
Thunderbolt USB-C portYes, it supports DP Alt Mode
USB-C port with DisplayPort Alt ModeYes
USB-C port for data or charging onlyNo video
USB 2.0 or SuperSpeed USB portNo video
USB-C to USB-C cableThe cable Dell says to use
USB-C to DisplayPort or USB-C to HDMI cableDell says this can cause the problem

That table comes from Dell’s article on its portable monitors (C1422H, P1424H and P1425), so check your own model’s manual before assuming the same limits apply.

If the computer’s USB-C port is unmarked, look in the computer’s manual to see whether it supports DP Alt Mode, and if it does not, use a different input on the monitor.

Roll back or reinstall the graphics driver

If the black screen began after a Windows or driver update, rolling back the graphics driver is Dell’s next step.

  1. Press the Windows key and Q, then search for Device Manager and open it.
  2. Expand Display adapters.
  3. Right-click the graphics adapter and choose Properties.
  4. Open the Driver tab and select Roll Back Driver if it is available.
  5. Restart the computer when prompted.

If Roll Back Driver is grayed out, download the latest video driver from Dell Drivers and Downloads using your Service Tag.

You can also restart the graphics drivers at any time by pressing Windows, Ctrl, Shift and B together, which gives a short beep and a screen flash.

Reset the monitor and check brightness

If the monitor has a picture but it looks black, Dell says to set brightness and contrast to their highest levels in the on-screen menu.

You can also reset the monitor to factory settings from the on-screen menu using its buttons or joystick.

The exact menu names differ by model, so Dell points you to the user guide you can find by searching your Service Tag or model number.

When to contact Dell support

Contact Dell Technical Support if the self-test shows lines, the buttons do not respond with only the power cable attached, or the monitor shows signs of a drop or liquid damage.

Dell notes that without an active accidental damage policy you pay for repairs to damaged monitors yourself.

Have your Service Tag or the model number ready, which is printed on a sticker on the back of the monitor.

If only a second screen is missing, see our guide to fixing a second monitor that is not detected on Windows 11.

If the screen goes dark for a moment and returns, read why a monitor goes black for a second.

If the picture never comes back after the computer sleeps, try fixing a monitor that will not wake up.

Sources: Dell’s display and video troubleshooting, monitor troubleshooting and USB-C no video articles.

Leave a Reply

Your email address will not be published. Required fields are marked *